Tectro R232TC Instrucciones De Uso página 27

10. Fit the control knob to the wick adjusting lever. Tilt down the weight of
10. Fit the control knob to the wick adjusting lever. Tilt down the weight of the
the tipover automatic extinguishing device and make sure the wick drops
10a
tipover automatic extinguishing device and make sure the wick drops quickly.
quickly. Repeat thes step 2 or 3 times fo added safety.
Repeat thes step 2 or 3 times fo added safety.
11. Press down the wick adjustment knob 2 and make sure that the dimension
11. Press down the wick adjustment knob ② and make sure that the dimension (c)
(c) between the wick cylinder' s top and the wick' s tip is 8.5-10 mm.
between the wick cylinder s top and the wick s tip is 8.5-10mm.
If the wick fails to drop or goes down too slowly, it means the wick holder is
If the wick fails to drop or goes down too slowly, it means the wick holder is
deformed or the wick running clearance is not uniform. Double-check for the
deformed or the wick running clearance is not uniform. Double-check for the
cause.
10b
cause.
Hold down the wick adjustment knob by hand and put a weight on it.
Hold down the wick adjustment knob by hand and put a weight on it.
(1) Loosen the coupler screw with a screwdriver.
(1) Loosen the coupler screw with a screwdriver.
(2) With the wick adjustment knob held down and the coupler pul led toward
(2) With the wick adjustment knob held down and the coupler pulled toward
yourself, tighten up the coupler screw.
yourself, tighten up the coupler screw.
* Makesure the screw is tight. Othewise the wick may get out of the specified
11
* Makesure the screw is tight. Othewise the wick may get out of the specified
height, resulting in poor heating.
height, resulting in poor heating.
(c)
12. Set the flame baffle' s right half onto the side of the wick cylinder. Then
12. Set the flame baffle s right half onto the side of the wick cylinder. Then fit the
fit the left half onto the side of the wick cylinder just below the right half
left half onto the side of the wick cylinder just below the right half from the
from the opposite direction. Catch the left half's hooks into the right half's
opposite direction. Catch the left half s hooks into the right half s square
square holes.
holes.
13. At this stage, remove the wick adjustment knob again. Reass enble the
13. At this stage, remove the wick adjustment knob again. Reassenble the heater
12
heater and put the refueling tank, combustion chamber and batteries in
and put the refueling tank, combustion chamber and batteries in position.
position. Place the combustion chamber just from above the wick fuide
Place the combustion chamber just from above the wick fuide with the
with the combustion chamber knob facing the front.
combustion chamber knob facing the front.
In placing the burner, be careful not to damage the ignition heater.
In placing the burner, be careful not to damage the ignition heater.
13
14. Push the wick adjustment knob deep to the wick adjusting lever.
14. Push the wick adjustment knob deep to the wick adjusting lever.
15. Wait for about 30 minutes until you use the heater with the new wick.
15. Wait for about 30 minutes until you use the heater with the new wick.
Do not ignite just after refueling. The wick that does not have enough
Do not ignite just after refueling. The wick that does not have enough kerosene
kerosene may fail to get the burner red hot.
may fail to get the burner red hot.
16. Be sure that the wick has sucked up enough kerosene. Now make an
16. Be sure that the wick has sucked up enough kerosene. Now make an ignition
14 ignition test. If it is hard to ignite, reposition the ignition heater.
test. If it is hard to ignite, reposition the ignition heater.
16
4
27