SPORT-ELEC Body control system Manual De Uso página 13

IV. uSE THE muLTIFunCTIonAL BELT
The multifunctional belt can be used whole, or separated into 2 to form 2 half-belts.
The full belt must be used on the stomach, lower back areas.
Once unfastened, the 2 "half-belts" can be used on the arms, thighs, or calf.
The multifunction belt has built-in electrodes on which the SPORT-ELEC® cream is applied. This cream enhances contact between
the electrodes and the skin. Its massaging and electro conducting properties improve comfort of use and enhance stimulation.
The cream can also be used for body massage.
If you want to buy the SPORT-ELEC® cream, please order directly by going on www.sport-elec.com, or contact your local supplier.
Never use the belt without the cream provided.
Do not use any cream other than the one provided by SPORT-ELEC® INSTITUT.
PRESENTATION OF THE BELT :
• Front side (photo B page 2) :
• Electrodes side (photo D page 2) : 4 built-in electrodes
STEP 1 : CONNECTING AND FITTING THE BELT.
• Check your SPORT-ELEC® unit is stopped.
• Take the connectors of your device and connect them to the belt connectors per groups of two (photo F page 2).
• Apply a thick layer of electro-conductive massaging cream onto the electrodes built into the belt (domed part - photo E page 2).
• Place the belt (or 2 half-belts) onto the zone(s) to be stimulated (stomach, back, arms, thighs, calf ), and adjust them using "scratch"
strips to ensure the built-in electrodes are properly in contact with the skin
• Move the belt slightly left or right (with device powered off ) to feel the contractions on the abdominal area.
• If an electrode hurts or if you feel any tingling, stop the device, and check the electrode is properly smeared with cream.
STEP 2 : STARTING THE BELT FUNCTION
Once your unit is connected, install yourself comfortably and start your unit using the procedure "Starting the unit" detailed previ-
ously in paragraph II.
STEP 3 : STOPPING THE BELT FUNCTION
Once the program is finished, disconnect the device from the belt.
Remove the excess cream on the built-in electrodes using a wipe dampened with water, then dry them.
V. uSE THE PAnTY
PRESENTATION OF THE PANTY :
• Front side (photo G page 2): 1 = Wire storage, 2 = Connection plugs, 3 = Scratch strap
• Electrode side : 4 built-in electrodes
STEP 1 : CONNECT AND INSTALL THE PANTY
- Make sure that your SPORT-ELEC® device is switched OFF.
- Take the connectors of the unit and plug them to the panty plugs by 2 groups (photo I - F page 2).
- Apply a thick layer of the electro-conducting cream to the built-in electrodes of the panty (the convex part - photo I - E page 2)
- Place the panty on your butts (photos I page 2 : G = butts).
STEP 2 : START A SESSION
Once your device is connected, make yourself comfortable and start your device following the procedure "Starting the unit" detailed
previously in paragraph II.
- Do not try to increase the intensity too quickly.
- If the power seems to you too strong, decrease it by pressing briefly on the "-". key.
A long press on the "-" key returns the power to its minimal level. This operation does not switch off the device.
- Do not hesitate to place the panty slightly to the left or right (after switching the power key on zero) in order to feel the contrac-
tions on the whole area of buttocks.
- If an electrode hurts or if you feel some tingling, it is necessary to stop the device and to verify whether the electrode is well
covered with cream.
STEP 3 : END OF THE SESSION
Once the program is finished, switch off the device and unplug it from the panty.
Remove the surplus of cream from the built-in electrodes with a moistened cloth and dry the belt. Store carefully your material.
= Fasteners ; = Wire storage ; = Connection terminals ; = Scratch strip
13