General Safety; General Outline; Technical Specifications - BFT SELETTO Instrucciones De Uso

Thank you for buying this product, our company is
sure that you will be more than satisfied with the
product's performance. The product is supplied with
a "Warnings" leaflet and an "Instruction booklet".
These should both be read carefully as they provide
important information about safety, installation,
operation and maintenance. This product complies
with the recognised technical standards and sa-
fety regulations. We declare that this product is in
conformity with the following European Directives:
2004/108/EEC and 73/23/EEC (and subsequent
amendments).

GENERAL SAFETY

WARNING! An incorrect installation or improper
use of the product can cause damage to persons,
animals or things.
• Scrap packing materials (plastic, cardboard, po-
lystyrene etc) according to the provisions set out
by current standards. Keep nylon or polystyrene
bags out of children's reach.
• Keep the instructions together with the technical
brochure for future reference.
• This product was exclusively designed and ma-
nufactured for the use specified in the present
documentation. Any other use not specified in
this documentation could damage the product
and be dangerous.
• The Company declines all responsibility for any
consequences resulting from improper use of
the product, or use which is different from that
expected and specified in the present documen-
tation.
• Do not install the product in explosive atmosphere.
• Disconnect the electrical power supply before
carrying out any work on the installation. Also
disconnect any buffer batteries, if fitted.
• Only use original parts for any maintenance or
repair operation.
• Instruct the product user about the control systems
provided and the manual opening operation in
case of emergency.
• Do not allow persons or children to remain in the
automation operation area.
• Keep radio control or other control devices out of
children's reach, in order to avoid unintentional
automation activation.
• The user must avoid any attempt to carry out work
or repair on the automation system, and always
request the assistance of qualified personnel.
• Anything which is not expressly provided for in
the present instructions, is not allowed.
• Fit an omnipolar or magnetothermal switch on the
mains power supply, having a contact opening
distance equal to or greater than 3,5 mm.
• Check that a differential switch with a 0.03A
threshold is fitted just before the power supply
mains.
INSTALLATION MANUAL
• The power supply must have a very low safety
voltage and the generator must be protected
against short circuit.

1) GENERAL OUTLINE

Programmable digital pushbutton panel for control-
ling pedestrian and vehicle access points using two
operating methods:
1 - Serial connection:
Manages control panels provided with serial
connection.
Up to 16 different codes can be memorised. Each
valid code sends a start command through the
serial line.
2 - Interfaced with a Compass system:
The pushbutton panel is integrated in the Com-
pass access control system.
Provided with an anti-break-in metal container,
the Seletto pushbutton panel does not directly
control access point opening. Therefore, it can
also be safely installed in unprotected areas.

2)TECHNICAL SPECIFICATIONS

Power supply: ................12/24 V
Absorption: ..................................................60 mA
Working temperature: ......................... -10 / +55°C
No. codes (serial connection): ........................... 16
Dimensions: ............................................ see fig. 1
Degree of protection: .....................................IP 44
3) INSTALLATION
Various types of mounting are possible:
3.1) Recessed mounting on wall (SELETTO)
Make a hole where the supplied plastic container is
to be inserted, this will be held in place by concrete
filling (Fig. 1a).
3 fixing clips are supplied (Fig. 1a "G") to be scre-
wed on the container before carrying out concrete
filling.
After the concrete has set, the 3 screws must be
removed to allow the gasket and metal ring nut to
be subsequently fitted.
3.2) Recessed mounting on metal pillar (SE-
LETTO)
Make a hole by means of a ø 60 milling cutter where
the supplied plastic container is to be inserted. To
fix the container, drill three ø 3.6 holes for the three
self-tapping screws.
3.3) External container mounting (SELETTO E)
Use the box as a drilling template and drill 4 holes.
Fix by means of self-tapping screws or expansion
plugs, depending on the surface the box is being
fixed on. Use the black sponge (H) between the
appliance and the wall (Fig.1b).
ENGLISH
~
/ ±10% 50Hz
SELETTO - Ver. 05 - 7