Technical Data - Bosch GSS 23 AE Professional Instrucciones De Servicio

Technical Data

Orbital sander
Article number
Rated power input
Preselection of orbital
stroke rate
No-load speed
Orbital stroke rate
Orbit diameter
Sanding sheet dimensions
— Adhesion via
Velcro backing
— Attachment via clamping
Sanding plate dimensions
Weight according to
EPTA-Procedure 01/2003
Protection class
The values given are valid for nominal voltages [U] of
230/240 V. For lower voltage and models for specific coun-
tries, these values can vary.
Please observe the article number on the type plate of your
machine. The trade names of the individual machines may
vary.
Noise/Vibration Information
Measured values determined according to EN 60745.
Typically the A-weighted sound pressure value of the
machine is 80 dB(A). Measuring uncertainty K=3 dB.
The noise level when working can exceed 85 dB(A).
Wear hearing protection!
The typically weighted acceleration is 4.0 m/s
Declaration of Conformity
We declare under our sole responsibility that this prod-
uct is in conformity with the following standards or
standardization documents: EN 60745 according to
the provisions of
98/37/EC.
Dr. Egbert Schneider
Senior Vice President
Engineering
Robert Bosch GmbH, Power Tools Division
GSS 23 AE
PROFESSIONAL
3 601 K70 7..
W
rpm 7000–12000
opm 14000–24000
mm
mm 93 x 185
mm 93 x 230
mm 92 x 182
kg
the directives 89/336/EEC,
Dr. Eckerhard Strötgen
Head of Product
Certification
Assembly
Dust/Chip Extraction
Integrated Dust Extraction with Dust Box
190
(see figures G1–G4)
Attach the dust box 4 onto the outlet piece 12 until it
latches.
To empty the dust box 4, pull off the dust box down-
ward.
2.0
Before opening the dust box 4, it is recommended to
loosen the dust from the filter element by gently striking
it against a firm support (as shown in the figure).
Grasp the dust box 4 by the recessed grip, fold the filter
element 13 upward and empty the dust box. Clean the
thin plates of the filter element 13 with a soft brush.
1.7
External Dust Extraction (see figure H)
/II
Insert a vacuum hose 14 onto the outlet piece 12. Con-
nect the vacuum hose 14 to a vacuum cleaner. See the
overview for connecting to various vacuum cleaners at
the end of these operating instructions.
The vacuum cleaner must be suitable for the material
being worked.
When vacuuming dry dust that is especially detrimental
to health or carcinogenic, use a special vacuum
cleaner.
Replacing the Sanding Sheet
Before any work on the machine itself, pull the
mains plug.
2
.
When attaching a new sanding sheet, remove any dust
or debris from the sanding plate 6 (e. g. with a brush).
To ensure optimum dust extraction, pay attention that
the punched holes in the sanding sheet match with the
holes in the sanding plate.
Sanding Sheets with Velcro Backing
(see figure A)
The sanding plate 6 is fitted with Velcro backing for
quick and easy fastening of sanding sheets with Velcro
adhesion.
Before attaching the sanding sheet 7, free the Velcro
backing of the sanding plate 6 from any debris by tap-
ping against it in order to enable optimum adhesion.
Position the sanding sheet 7 flush alongside one edge
of the sanding plate 6, then lay the sanding sheet onto
the sanding plate and press it against it with a light turn-
ing motion in clockwise direction.
To remove the sanding sheet 7, grasp it at one of the
tips and pull it off from the sanding plate 6.
English–3