ESTEBAN CMP 142 Instrucciones De Uso página 9

Difusor bruma de perfume
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 18
4
OPERATION AND MAINTENANCE INSTRUCTIONS
CLEANING
After each use, to avoid spotting and bad smells clean the appliance
by following these steps:
• switch it off and/or unplug from the mains
 TAKE CARE NOT TO TILT THE DIFFUSER IF THERE IS
ANY WATER IN THE CONTAINER
• remove the two upper parts A and B
• empty out the container by following the direction of the arrow
placed on the bottom of the container to avoid any contact with
electrical parts
• clean the water container in order to remove all residues, for it use
absorbent paper impregnated with a mild detergent (soap, washing-
up liquid... Do not use aerosol sprays, solvents or abrasive products
that might damage the appliance).
Then wipe it with a dry cloth
• use a soft cloth with a little of water if necessary to clean the
outside of the appliance
• use a wet cotton bud (water only) to clean the ceramic disk
• as this disk is very fragile and sensitive, make sure not to press too
strong and clean it after each use for longer operating life.
REPAIR
If the product is not working properly, check the following points:
Problems / Symptoms
The diffuser does not start up
or switches off during diffusion
No mist when the appliance is
switched on
Mist stops while the diffuser is
in operation
Insufficient mist
The remote control does
not work
Should the problems persist please contact your retailer.
The manufacturer is not responsible for damages caused by improper use of the diffuser.
STAGE 4
• The appliance stops automatically if the battery level is too low (a red light blinks) and/or there is
not enough water (a blue light blinks).
• Unplug the appliance, then empty out the remaining water by following the direction of
the arrow placed on the bottom of the container and clean it (refer to the "CLEANING"
recommendations in the operation and maintenance instructions).
Causes
The battery has run out or does not have enough charge
Water level too low
Water level exceeds 250 ml
The ends of parts A and B are obstructed
Water level too low
Accumulation of water drops on the end of part B
Accumulation of water drops on the air outflow D
(see plan on "OVERVIEW")
The ceramic disk is dirty
An excess of Estéban refresher oils or essential oils has
been poured into the container
Accumulation of water drops on the end of part B
The battery is worn out
The diffuser does not detect the remote control
NEW USE
•  if you charge your diffuser when there is water left in the
container, take care not to tilt the diffuser when connecting
the energy supply cable
• see STAGE 1 and STAGE 2 of the section "STARTING THE
DIFFUSER"
• replace the water in the container frequently to avoid any residue
that might damage the appliance
• empty out the liquid remaining after each use and clean the water
container and its ceramic disk each time you change the water or
fragrance, for an optimum fragrance.
LONG PERIOD WITHOUT USE
If the appliance is not going to be used during a long period, clean
it, dry it (by following the instructions in section "CLEANING"), and
keep it in a dry place.
Connect the electric cable to the underside of the device
ensuring you do not tilt it if there is any water left in
the container, and connect it to the mains. Wait until the
device battery is completely recharged (green light on)
Fill the water container
Empty out excess water
Make sure that nothing is preventing the release of the mist
Fill the water container
Switch off the diffuser, remove parts A and B then clean off
the accumulated water drops
Switch off the diffuser, remove parts A and B then clean off
the accumulated water drops
Clean the ceramic disk as described in the "CLEANING"
instructions
Empty the appliance and clean it
Switch off the diffuser, remove parts A and B then clean off
the accumulated water drops
Replace it with a CR 2032 battery
Place properly the remote control in the diffuser direction
Solutions
9

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Cmp 143

Tabla de contenido