Shark GI405Z Manual Del Propietário página 3

FEATURES OF YOUR
INTELLIGENT ELECTRONIC IRON
3
2 1
4
1. BURST OF STEAM/X-TENDED
TM
STEAM BURST BUTTON
Turn the button counter clockwise
all the way to the left for quick
bursts of steam to aid in removing
stubborn wrinkles from fabrics such
as denim, cotton or linen.
Turn the button clockwise all the
way to right to get prolonged bursts
of steam. The iron in the X-Tended
steam position can be used
vertically as well as horizontally.
ATOMIZER SPRAY BUTTON
2.
Pressing this button provides a
defined jet of spray which gently
moistens fabric.
VARIABLE STEAM CONTROL
3.
Minimum to maximum steaming for
different materials. Self cleaning
feature flushes internal sole plate
with water.
ELECTRONIC TEMPERATURE
4.
CONTROL
Select the fabric setting and
temperature indicator by pressing
on this button.
ANTI-DRIP FUNCTION
5.
Cuts off water when the iron
temperature is too low.
BUILT-IN ANTI-CALCIUM
6.
FILTER
Prevents calcium build-up and
prolongs the life of the iron.
LED Display Panel
LED DISPLAY PANEL
7.
Displays the fabric setting (left) and
the temperature indicators (right).
WATER FILLING INLET
8.
The cover prevents dust and
foreign matter from entering the
water tank. It also stops any water
from spilling during ironing.
STAINLESS STEEL
9.
SOLEPLATE
Provides maximum glide-ability
and heat retention.
PIVOT CORD
10.
For left or right handed use. Pivots
up and down; prevents dragging
along the fabric. The flexible cord
protector protects the cord from
fraying.
3
OPERATING INSTRUCTIONS
This appliance is for HOUSEHOLD
USE ONLY and may be plugged into
any 120V AC polarized electrical outlet.
Do not use any other type of outlet.
FABRIC & TEMPERATURE
INDICATORS
Press on the Electronic Temperature
Control to select the desired fabric
setting. The lights at the left of the LED
Display Panel will light up. At the same
time, the temperature indicator lights on
the right side of the LED Display Panel
will start to flash. They will stop flashing
when the iron reaches the selected
temperature.
DRY IRONING
For dry ironing, turn the variable steam
control dial all the way to the right to
"0". This will cut off the steam flow if
water is in the water tank. All marked
fabric settings on the LED Display
Panel can be used for dry ironing.
1. Plug the cord into a polarized, 120V
AC electrical outlet. The power "ON"
light will come on, indicating that the
iron is receiving power.
2. Press on the electronic temperature
control button to select the desired
fabric/temperature setting. Turn the
variable steam control dial to "0".
(See "Ironing Guide" for a guide to
temperature selection.)
3. Place iron on its heel (on a stable,
protected surface) while iron is
warming to desired temperature.
STEAM IRONING
Caution:
DO NOT aim iron at face,
towards yourself, or anyone else
while using or adjusting steam.
Burns or serious injury may occur.
Warning:
Before filling the iron with
water, be sure the iron is not
plugged into the electrical outlet.
The iron may be filled with water
while it is hot.
Caution:
TO PREVENT THE RISK
OF BURNS, use caution when filling
iron with water. Burns can occur
from touching hot metal parts, hot
water, or steam.
Note:
Because of the soleplate design,
ordinary tap water may be used with this
iron. However, in very hard water areas,
we recommend using distilled or
demineralized water.
Warning: Never fill the iron with
fabric conditioner, starches or any
other liquid, as these will damage the
steam mechanism. Do not use
contaminated water.
1. Open the water filling inlet cover.
Holding the iron at a slight angle,
pour water slowly into the water
filling inlet. (Fig.1) Fill tank to
desired level or to the "MAX" water
level marking using the water filling
flask. (When the iron is upright, the
see-through water tank allows you to
gauge the amount of water.)
DO NOT overfill the tank. When
finished filling the iron with water,
close the water inlet cover before
continuing.
Fig. 1
2. Plug the cord into a polarized, 120V
AC electrical outlet.
3. Press on the electronic temperature
control button to select the desired
fabric and temperature setting. Turn
the variable steam control dial to the
desired steam setting. (See "Ironing
Guide" for a guide to temperature
selection.)
4