Taurus ACTIVE PROFESSIONAL 1500 Manual De Instrucciones página 10

INSTRUCTIONS FOR USE
BEFORE USE:
- Make sure that all products' packaging has
been removed.
- Before using the product for the first time, clean
the parts that will come into contact with food in
the manner described in the cleaning section.
USE:
- Unroll the cable completely before plugging it in.
- Place the jar onto to the motor unit until it fits
properly into place (Fig.1).
- Put the ingredients, after having first chopped
them into small piece, into the jar with liquid (do
not exceed the maximum marker).
- Use stirrer bar to introduce food easily.
- Put the lid on the jar; make sure it is properly
fixed in place.
- Put the transparent cup in the lid.
- Connect the appliance to the mains.
- Start the appliance by turning on the ON/OFF
button (F). ATTENTION: before turn on the ON
button, be sure to set the minium speed.
- Choose desired speed using the speed regula-
tor control and start blending. ATTENTION: hold
the jar if uses high speeds.
- If you wish to add more ingredients pull out the
transparent cup.
- Add the ingredients and replace the transparent
cup.
- To stop the appliance, selecting OFF option of
the button (F).
- To avoid a fierce, start up of the fan, it is advis-
able to start off from the lowest speed position
and, once the fan has been switched on,
progressively increase the speed to the desired
position.
ELECTRONIC SPEED CONTROL:
- The speed of the appliance can be regulated
by using the speed regulator control (G). This
function is very useful, as it makes it possible to
adapt the speed of the appliance to the type of
work that needs to be done.
ONCE YOU HAVE FINISHED USING THE
APPLIANCE:
- Stop the appliance, selecting OFF option of the
button (F).
- Unplug the appliance from the mains.
- Lift the jar from the motor body.
- Clean the appliance.
"PULSE / ICE CRUSH" FUNCTION
- The appliance works in highest speed to
achieve optimal performance.
- Turn on this button to operate and release the
button when you wish to stop operating.
- This function gives optimal result for ice-crush-
ing, up to desired snowy level.
- We recommend working by turning on the
button in cycles of 3 seconds and repeating the
operation until you obtain the desired result.
CABLE COMPARTMENT
- This appliance has a cable compartment situat-
ed on its underside (I).
SAFETY THERMAL PROTECTOR:
- The appliance has a safety device, which pro-
tects the appliance from overheating.
- If the appliance turns itself off and does not
switch itself on again, disconnect it from the
mains supply, and
- In the event of overheating, the thermal safety
mechanism will be activated and the appliance
will stop operating. When this occurs, the ap-
pliance should be disconnected from the mains
and left to cool. Then press the rearming button,
situated at the bottom of the appliance, with the
tip of a pen or similar in order to reactivate the
appliance. (Fig.2)
- Wait for approximately 15 minutes before re-
connecting. If the machine does not start again
seek authorised technical assistance.
CLEANING
- Disconnect the appliance from the mains and
allow it to cool before undertaking any cleaning
task.
- Clean the equipment with a damp cloth with a
few drops of washing-up liquid and then dry.
- Do not use solvents, or products with an acid or
base pH such as bleach, or abrasive products,
for cleaning the appliance.
- Do not let water or any other liquid get into the
air vents to avoid damage to the inner parts of
the appliance.
- Never submerge the appliance in water or any
other liquid or place it under running water.
- During the cleaning process, take special care
with the blades, as they are very sharp.
- It is advisable to clean the appliance regularly
and remove any food remains.
- The following pieces may be washed in a dish-
washer (using a soft cleaning program):