System Exclusive Message - Roland RD-700 Manual Del Usuario

Tabla de contenido

Publicidad

MIDI Implementado
Channel Mode Messages
All Sounds Off (Controller number 120)
Status
2nd byte
BnH
78H
n = MIDI channel number: 0H - FH (ch.1 - 16)
* When this message is received, all notes currently sounding on the corresponding
channel will be turned off.
Reset All Controllers (Controller number 121)
Status
2nd byte
BnH
79H
n = MIDI channel number: 0H - FH (ch.1 - 16)
* When this message is received, the following controllers will be set to their reset values.
Controller
Pitch Bend Change
Channel Pressure
Modulation
Breath Type
Expression
Hold 1
Sostenuto
Soft
Hold 2
RPN
NRPN
All Notes Off (Controller number 123)
Status
2nd byte
BnH
7BH
n = MIDI channel number: 0H - FH (ch.1 - 16)
* When All Notes Off is received, all notes on the corresponding channel will be turned
off. However, if Hold 1 or Sostenuto is ON, the sound will be continued until these are
turned off.
OMNI OFF (Controller number 124)
Status
2nd byte
BnH
7CH
n = MIDI channel number: 0H - FH (ch.1 - 16)
* The same processing will be carried out as when All Notes Off is received.
OMNI ON (Controller number 125)
Status
2nd byte
BnH
7DH
n = MIDI channel number: 0H - FH (ch.1 - 16)
* The same processing will be carried out as when All Notes Off is received. OMNI ON
will not be turned on.
MONO (Controller number 126)
Status
2nd byte
BnH
7EH
n = MIDI channel number:
mm = mono number:
* The same processing will be carried out as when All Notes Off is received.
* The Mono/Poly parameter (EDIT:Tone Edit:Mono/Poly) will change.
POLY (Controller number 127)
Status
2nd byte
BnH
7FH
n = MIDI channel number: 0H - FH (ch.1 - 16)
* The same processing will be carried out as when All Notes Off is received.
* The Mono/Poly parameter (EDIT:Tone Edit:Mono/Poly) will change.
148
3rd byte
00H
3rd byte
00H
Reset value
±0 (center)
0 (off)
0 (off)
0 (min)
127 (max)
0 (off)
0 (off)
0 (off)
0 (off)
unset; previously set data will not change
unset; previously set data will not change
3rd byte
00H
3rd byte
00H
3rd byte
00H
3rd byte
mmH
0H - FH (ch.1 - 16)
00H - 10H (0 - 16)
3rd byte
00H
System Realtime Message
Timing Clock
Status
F8H
* This message will be received if the Clock Source parameter (EDIT:SYSTEM:Clock
Source) is MIDI.
Active Sensing
Status
FEH
* When Active Sensing is received, the unit will begin monitoring the intervals of all
further messages. While monitoring, if the interval between messages exceeds 420 ms,
the same processing will be carried out as when All Sounds Off, All Notes Off and Reset
All Controllers are received, and message interval monitoring will be halted.

System Exclusive Message

Status
Data byte
F0H
iiH, ddH, ......,eeH
F0H:
System Exclusive Message status
ii = ID number:
an ID number (manufacturer ID) to indicate the manufacturer whose
Exclusive message this is. RolandsmanufacturerIDis41H.'
ID numbers 7EH and 7FH are extensions of the MIDI standard;
Universal Non-realtime Messages (7EH) and Universal Realtime
Messages (7FH).
dd,...,ee = data:
00H - 7FH (0 - 127)
F7H:
EOX (End Of Exclusive)
Of the System Exclusive messages received by this device, the Universal Non-realtime
messages and the Universal Realtime messages and the Data Request (RQ1) messages and
the Data Set (DT1) messages will be set automatically.
Universal Non-realtime System Exclusive Messages
Identity Request Message
Status
Data byte
F0H
7EH, dev, 06H, 01H
Byte
Explanation
F0H
Exclusive status
7EH
ID number (Universal Non-realtime Message)
dev
Device ID (dev: 00H - 1FH (1 - 32), the initial value is 10H (17).)
06H
Sub ID#1 (General Information)
01H
Sub ID#2 (Identity Request)
F7H
EOX (End Of Exclusive)
* When this message is received, Identity Reply message (p. 153) will be transmitted.
GM1 System On
Status
Data byte
F0H
7EH, 7FH, 09H, 01H
Byte
Explanation
F0H
Exclusive status
7EH
ID number (Universal Non-realtime Message)
7FH
Device ID (Broadcast)
09H
Sub ID#1 (General MIDI Message)
01H
Sub ID#2 (General MIDI 1 On)
F7H
EOX (End Of Exclusive)
* When this messages is received, this instrument will turn to the GM mode.
* Not received when the Rx GM1 System On parameter (EDIT:System:Rx GM1 System
ON) is OFF.
Status
F7H
Status
F7H
Status
F7H

Publicidad

Tabla de contenido
loading

Tabla de contenido