Assembly; Declaration Of Conformity; Battery Charging; Fitting/Replacing The Battery - Wiha speedE Manual Del Usuario

ASSEMBLY

Declaration of Conformity

We declare under our sole responsibility that the product described under "Technical Data" is in conformity with all relevant provisions of the directives 2009/125/EC (Regulation
1194/2012), 2011/65/EU, until 19 April 2016: 2004/108/EC, from 20 April 2016 on: 2014/30/EU, 2006/42/EC including their amendments and complies with the following standards: EN
62841-1, EN 62841-2-1, EN 62841-2-2, EN 50581.
Technical file (2006/42/EC) at:
Wiha Werkzeuge GmbH
Obertalstraße 3-7
D-78136 Schonach
Wilhelm Hahn
Geschäftsführer / Director
Wiha Werkzeuge GmbH
Obertalstraße 3-7, 78136 Schonach
13.10.2017
Assembly

1. Battery Charging

Only use the charger supplied in the delivery package. This is the only charger suited to the Li ion battery used in your screwdriver.
Note: The battery is partially charged when delivered. Fully charge the battery
battery is protected against complete discharge during use. The speedE is switched off by a protection circuit if the battery
and the speedE can now only be used as a normal screwdriver.

2. Fitting/replacing the battery

Open the end cap by twisting in an anti-clockwise direction. To change the battery, remove the empty battery
the screwdriver handle . Ensure the battery
Note: If the light flashes, it indicates that the speedE battery is low (<20%). The electric assisted screw-driving will still work when the charge level is at 20%. If the charge level
continues to fall, only the light will work to indicate that the battery

3. Insert slimVario bit

Insert the Wiha slimVario bit correctly into the speedE's bit chuck

4. slimVario bit change

Pull out the Wiha slimVario bit to remove. Since the bit
Note: Use the VDE-tested Wiha slimVario bit system with a 6 mm chuck.

Noise/Vibration Information

Sound emission values determined according to EN 62841. Typically the A-weighted sound pressure level of the product is 70 dB(A). Uncertainty K=3 dB.
The noise level when working can exceed 80 dB(A). Wear hearing protection! Vibration total values ah (triax vector sum) and uncertainty K determined according to EN 62841. Drilling into
metal: ah<2.5 m/s², K =1.5 m/s² Screwdriving without impact: ah<2.5 m/s², K =1.5 m/s². The vibration level given in this information sheet has been
measured in accordance with a standardised test given in EN 62841 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure. The
declared vibration emission level represents the main applications of the tool. However if the tool is used for different applications, with different accessories or insertion tools or is poorly
maintained, the vibration emission may differ. This may significantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running but not actually doing the job. This may
significantly reduce the exposure level over the total working period. Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and
the accessories, keep the hands warm, organisation of work patterns.
12
in the charger before using it for the first time to ensure it delivers optimum performance. The Li ion
pole terminals are in the right position („-" in the end cap
is empty.
. The bit chuck
is not locked into position separately, it can be removed by twisting against the clamp hold.
from the screwdriver handle
). Replace the end cap
clamps the bit to the screwdriver handle.
is low: The electric assisted screw-driving no longer works
. Then insert the charged battery
on the speedE, turning it in a clockwise direction.
into