Serial Numbers; Cleaning And Maintenance; Product Maintenance - Peg-Perego pliko p3 compact Instrucciones De Uso

be created to allow more air to circulate and watch the
child when sleeping.
13 5-POINT SAFETY HARNESS: to fasten, insert the two
buckles of the waist strap (with attached shoulder
straps, arrow a) into the leg divider strap until they
click into place (arrow b). To unfasten them, press the
button which is situated in the centre of the fastener
(arrow c) and pull the waist strap outwards (arrow d).
14 To tighten the waist strap, pull on both sides in the
direction of the arrow. To loosen it do the opposite.
15 To adjust the height of the safety harnesses, release
the two buckles on the rear of the backrest.
Pull the shoulder straps towards you (arrow a) until the
buckles are released and insert them in the backrest
loops (arrow b). Remove the shoulder straps from the
sack (arrow c) and insert them in the most appropriate
buckle (arrow d), then reattach the two buckles
behind the backrest (arrow e). The buckles are securely
attached when a click is heard (fig f).
16 ADJUSTING THE FOOTREST: the footrest can be
adjusted to three positions. To lower the footrest, pull
the two side levers downwards while lowering the
footrest. To lift the footrest, pull it upwards until it
clicks into place.
17 ADJUSTING THE BACKREST: the backrest reclines to
four different positions. To lower the backrest, lift the
handle while lowering the backrest, locking it in the
desired position. To raise it, pull the backrest upwards.
18 FRONT BAR: to fasten the front bar, slip both ends of
the front bar into the armrests until it clicks into place.
19 The front bar can be opened to one side only to allow
the child to get in and out of the stroller easier when
he or she is older. To open the front bar, press the
button under the armrest while pulling out the front
bar (Fig.a). To remove the front bar, press the two
buttons under the armrests while pulling out the front
bar (Fig.b).
20 When removing the front bumper, insert the plugs
provided to close the armrests of the chassis.
21 REAR LEDGE: the rear ledge helps the mother
overcome small bumps and can also be used to carry a
second child (fig_a).
LOADING SEQUENCE: to use the PLIKO P3 COMPACT
with two children (fig_b), first set the brakes on the
stroller, then place the smaller child in the seat and
fasten the safety harness (1). Hold the handlebars (2)
and have the second child stand on the ledge (3).
Never leave your children unattended.
Do not allow a child to stand on the rear ledge when
the stroller is empty.
22 FOLDING UP: before folding up PLIKO P3 COMPACT,
remove the Navetta XL or the PrimoViaggio car
seat. The stroller can be folded up using one hand
only: pull first one lever upwards and then the other,
until they click.
23 Hold the central handlebar and pull it upwards until
the stroller folds up (fig_a). Check the correct closure
of the chassis from the safety hook (fig_b).
When folded, the chassis will stand upright .
24 CARRYING: PLIKO P3 COMPACT can be conveniently
carried by the central handle (with the front wheels set
on stationary) (fig.a). It can also be carried by the side
handle (fig_b).
25 REMOVABLE LINING: To remove the lining from the
stroller:. unhook the sack attachments from the
armrests in the order indicated (fig_a);. unfasten the
sack button at the sides;. remove the sack from the
footrest;. slide the leg divider part of the strap from
under the seat (fig_b);
26 unfasten the sack buttons from the seat;. unscrew the
strap (only on one side),by keeping your finger under
the nut; slide it downwards
GANCIOMATIC SYSTEM
Ganciomatic is the quick and practical system that
allows you to attach the Navetta XL or the Primo
Viaggio (0+ group) which are also equipped with
the Ganciomatic system, to the Pliko P3 Compact in
stroller format, thanks to its Ganciomatic connectors.
THE STROLLER GANCIOMATIC FASTENERS
27
to raise the Ganciomatic connectors on the stroller, lift
the fabric covering at the corners of the seat, pull the
lever outwards and at the same time swivel the two
connectors upwards until they click (fig_a).
To lower the stroller Ganciomatic fasteners, pull
the lever outwards and at the same time rotate the
fasteners downwards (fig_b).
PLIKO 3 COMPACT + Navetta XL:
To attach the carrycot to you must:
- block the PLIKO P3 COMPACT
- lift the Ganciomatic clasps in the frame
- remove the bumper bar (step 19) and insert the tops
into the chassis armrests.
- raise the footrest to its highest position;
- hold the Navetta by its handlebar;
28 place the Navetta on the Ganciomatic hooks on the
stroller, keeping the head of the bassinet unit on the
opposite side from the stroller handlebars;
- press down with both hands on the sides of the
Navetta, until it clicks into place (fig_a);
- to remove the Navetta from the chassis and for more
information, please refer to the instruction manual.
PLIKO P3 COMPACT + Primo Viaggio (0+ group):
To attach the car seat you must:
- block the chassis
- lift the Ganciomatic clasps in the frame
- put the car seat in face-mum position and push it
downwards until it clicks (fig_b)
- Do not remove the bumper bar from the pushchair
when you attach the car seat (please read step 18 for
information on how to put on the bumper bar)
- Remove the car seat according to the car seat's
instructions

SERIAL NUMBERS

29 Behind the PLIKO P3 COMPACT backrest information
relating to product name, date of manufacture and
serial number of the product are provided. This
information is required for any complaints.
ACCESSORIES
30 RAIN COVER: can be fastened to the hood (fig_a).
MOSQUITO NETTING: can be fastened to the hood (fig_b).
31 BAG: diaper-changing bag with pad for changing
baby's diaper. Attaches to the stroller (fig_a).
TRAVEL BAG: practical duffle bag for transporting the
stroller by plane (fig_b).
PARASOL: practical umbrella to match (fig_c).
32 CUP HOLDER: may be attached to the mushroom
button on the frame of the stroller (fig. a).
BABY CUSHION for Peg Perego high chairs and strollers.
Winter side made with cozy matelassé jersey and
summer side made with 100% cotton (fig_b).
VARIO FOOT MUFF: a warm, light and soft multi-
purpose foot muff. Can be used as a changing mat
and adjusted to 3 sizes (fig_c).

CLEANING AND MAINTENANCE

PRODUCT MAINTENANCE: protect from the weather:
water, rain, or snow; prolonged and continuous
exposure to bright sunlight may give rise to colour
changes of various different materials; store this product
in a dry place.The maintenance have to be regularly.
CLEANING THE CHASSIS: periodically clean all plastic parts
with a damp cloth. Do not use solvent or similar cleaning
products; keep all metal parts dry to prevent rusting; keep
moving parts clean (adjustment mechanisms, locking
mechanisms, wheels, ...) and free of dust and sand and, if
necessary, lubricate with light machine oil.
CLEANING THE RAIN CANOPY: wash with a sponge and
soapy water; do not use detergents.
- 18 -
: