Controls And Functions - JB Systems MCD 300 Manual De Instrucciones

ENGLISH
CLEANING THE CD-PLAYER:
Clean by wiping with a polished cloth slightly dipped with water. Avoid getting water
inside the unit. Do not use volatile liquids such as benzene or thinner which will
damage the unit.
CONNECTIONS
• Use the supplied cinch cables to connect the audio outputs of the CD player with
the CD or line inputs on your mixing unit.
• Connect the mains cable.

CONTROLS AND FUNCTIONS

1. SEARCH WHEEL (OUTER RING): This wheel has 4 forward and 4 backward
speed positions for searching through songs. The more you turn the wheel in
either direction the faster you will search through the music.
2. JOG WHEEL (INNER RING): This jog wheel serves 2 functions depending on
the mode you are working in.
• The jog wheel acts as a slow frame search (1/75sec) control when the CD is
not playing but either paused or set to a cue point. To set a new cue point,
spin the wheel and press PLAY when you have determined the proper
position. Press CUE to return to the "CUE POINT".
• The jog wheel temporarily bends the pitch of the music up to +/-16% if the
song is already playing by rotating the wheel clockwise to speed up or
counterclockwise to slow down. The amount of pitch change is determined by
the speed of rotation.
3. TRACK SEARCH Buttons: These buttons are used to select the track to be
played. Forward skip & back skip. Press the +10 button to skip 10 tracks at once.
4. CUE button: Pressing the CUE button during play provides an immediate return
to the position at which play was started. Playback is started immediately from
the programmed cue point for as long as the CUE button is pressed. The CD
player jumps back to the cue point as soon as the CUE button is released. Also
with the unit in pause mode (Play/Pause LED blinks) the search and/or jog wheel
is used to set a different start point. By pressing "PLAY/PAUSE" button then
"CUE", you can confirm this new cue point. The CUE LED will light up since the
cue button is pressed until the CD has returned to the position at which play was
started.
JB SYSTEMS®
USER MANUAL
3/38 MCD300
ENGLISH
5. PLAY/PAUSE button: every time you press the PLAY/PAUSE button the CD
player changes from play to pause or from pause to play.
6. PITCH BEND buttons: The speed rises while the "+ button" is pressed and
return to the original pitch when the button is released. The pitch drops when the
"– button" is pressed and returns to the original pitch when the button is released.
These buttons can be used to synchronize the beats of 2 tracks.
7. PITCH button: This button is used to turn the Pitch function on and off. If you
want to change the speed adjustment range (+/- 8%, +/- 12% , +/- 16%), press
and hold PITCH button then press the PITCH BEND+ to select.
8. PITCH slider: Press the PITCH button, the PITCH LED is on. The speed can be
changed up to +/-16% by moving the sliding fader. The speed will not change if
the PITCH LED is off.
9. OPEN/CLOSE button: press this button to open and close the disc tray in the
front of the main unit. This button is disabled during playback. If the tray is not
closed after 60sec. It will close automatically to prevent mechanical damage.
10. TIME Button: The TIME button switches between elapsed playing time,
remaining time in a selection and total remaining time of the disc. (standard =
remaining /track)
11. SGL/CTN Button: with this button you can choose between "single track mode"
and "continuous play".
• Continuous play: the complete CD will be played without interruption.
(mostly used in pubs)
• Single track: player stops at the end of each track and waits at the beginning
of the next track. The player will wait at the first music note of each track.
12. PROGRAM Button: It is possible to program up to 20 tracks on each deck. After
programming the tracks will be played in the order you programmed. You can
also use the relay function to make a preprogrammed sequence on the 2 decks.
Follow the steps below for programming:
• Press the PROGRAM button once, the led next to it turns on and the display
shows "-- P-01 00".
• Choose the first track in your sequence and press the PROGRAM button.
The first track is programmed, the display shows "-- P-02 01"
• Choose the second track in your sequence and press the PROGRAM button.
The second track is programmed, the display shows "-- P-03 02"
• Continue these steps until you are finished.
• Now simply press the "play/pause button" to start the sequence. The first
track in your sequence starts playing while the display shows"** P-01"
The programmed sequence plays in an endless loop until you stop the program
mode by pressing the PROGRAM button for about 2 seconds". The led next to
the PROGRAM button turns off and the program memory is cleared.
13. LCD DISPLAY: Shows all important information needed during playback. Refer
to the next chapter for more information.
14. LOOP Button: Used to make the music play in a loop, follow the steps below to
create a loop:
• Make sure that the track is playing.
• Press the LOOP button to set the beginning of the loop: led starts flashing.
• Press the LOOP button again to set the end of the loop: led is on and the
music starts playing in loop mode.
• Press the LOOP button again to stop the loop mode: the led turns off.
JB SYSTEMS®
USER MANUAL
4/38 MCD300