Pioneer SC-LX801 Manual De Instrucciones página 28

> Before start > Hookup
"USB" input selector.
4. To adjust the volume on the power amplifier in the
separate room or the ZONE speaker, adjust with VOL+/–
on the remote controller. To control on the main unit,
press ZONE CONTROL several times to display either
"Z2" or "Z3" in the display, and within 8 seconds, adjust
with the MASTER VOLUME dial.
0 The information for a connected device can be displayed
on the TV screen in a separate room. Press the
button while the remote controller is in the mode for
controlling ZONE 2.
0 Power consumption in standby mode increases when the
multi-zone function is being used.
To turn off the function
Press Í while in the mode for controlling ZONE 2 or ZONE
3 on the remote controller.
Playing in ZONE 2 or ZONE 3 only
If you turn the unit to standby during multi-zone playback,
the Z2 or Z3 indicator is dimmed and the playback mode is
switched to playback in a separate room only. Setting
ZONE 2/ZONE 3 to on while this unit is in standby will also
switch the playback mode to the same setting.
MULTI-ZONE MUSIC
If you press MULTI-ZONE MUSIC while playback is being
performed in the main room, the MULTI-ZONE MUSIC is
turned on, "Z2" and "Z3" on the display light at the same
time and the playback sources of all the rooms are switched
to the same source at once.
0 The sources that can be played in ZONE 2 can be played
in all rooms.
0 This function cannot be used if headphones are
connected or audio is output from the speakers of the TV.
Settings
Settings are required in Initial Setup, "4. Multi Zone Setup"
( P23) to use the multi-zone feature. When checking the

setting content, refer to the following, press
remote controller, and check in "System Setup" in the
28
> Setup > Playback
Home that is displayed.
– When you have connected a TV in the separate room
with an HDMI cable, have you selected "Use" in "Input/
Output Assign" – "TV Out/OSD" – "Zone2 HDMI"?
– When you are playing the audio from an AV component
with an HDMI cable in the separate room, have you
selected "Use" in "Input/Output Assign" – "TV Out/OSD"
– "Zone2 HDMI"?
– When you have connected speakers in a separate room
with speaker cable, have you selected "Zone 2" or "Zone
2/Zone 3" in "Speaker" – "Configuration" – "Zone
Speaker"?
– When you have connected a power amplifier in a
separate room with an analog audio cable and you want
to control the volume with this unit, have you selected
"Variable" in "Multi Zone" – "Zone 2" or "Zone 3" –
"Output Level"?
on the
> Part Names
AV Adjust
By pressing on the remote controller during play, you
can adjust frequently used settings, such as the switching
the speakers and adjusting sound quality, using on-screen
menus. Select the item with the cursors of the remote
controller and press ENTER to confirm your selection. To
return to the previous screen, press
no display on the TV screen when the input selector is
"CD", "TV", "PHONO", "FM", or "AM", so follow the main
unit's display while doing the operations.
AV Adjust
Tone Bass
Level Treble
MCACC
Other
"Tone": It is possible to enhance or moderate the bass and
treble of front speakers.
"Other": Enables you to make a variety of settings.
0 "Sound Delay": If the video is behind the audio, you can
delay the audio to offset the gap.
0 "Sound Retriever": Improve the quality of compressed
audio.
0 "Speakers": You can switch the output for speakers A/B.
0 "HDMI Out": Allows you to select the HDMI OUT jack to
output video signals from "MAIN", "SUB", and
"MAIN+SUB".
. Note that there is
BD/DVD