Nice UST1K Serie Instrucciones E Indicaciones Para La Instalación Y El Uso página 27

ASSEMBLY - SETTING
(also see fig. 12-14)
Setting of the final positions
Set the switch DIP 1 on "ON". The upper
ON
SAB
ON
SAB
horizontal bar of the display flashes.
1 2 3 4
1 2 3 4
Setting of the upper final position:
with the UP and DOWN buttons in deadman
mode, move the door to the upper final position
and store this position by briefly pressing the T2
button.
It is necessary to reverse the counting
direction of the electrical transmitter if
error 6 is shown on the display and the
door blocks during movement in the UP
direction.
ON
SAB
1 2 3 4 Set DIP switches 1 to 4 on "ON".
A small "u" appears on the display. To reverse
the counting direction, press button T2 (above
ON
SAB
the DIP switch) and keep it pressed until the u
turns 180° on the display.
1 2 3 4
Now put DIP switches 2, 3 and 4 on "OFF" ­
ON
SAB
return to setting the upper final position.
1 2 3 4
Now the lower horizontal bar flashes.
Setting of the lower final position:
With the UP and DOWN buttons in deadman
mode, move the door up to the lower final
ON
SAB
position and store this position by briefly
ON
SAB
pressing the T2 button.
ON
SAB
1 2 3 4
Now the central horizontal bar flashes.
1 2 3 4
1 2 3 4
ON ATTENTION!
SAB
The preliminary limit switch is automatically
set by the control unit when programming
1 2 3 4
the lower final position at about 5 cm above
the lower final position!!!
Partial opening setting
If you want to set a partial opening, now it is
possible to adjust the desired opening by
pressing the UP and DOWN buttons. Press the
T2 button to confirm the position.
Now the display switches off.
ON
SAB
1 2 3 4
ON
SAB
1 2 3 4
SETTINGS - FINAL POSITIONS
Then put the DIP switch 1 on "OFF". Now
the lower bar remains lit, while the central bar
flashes.
Check final positions
Move the door UP (upper final position) and
DOWN (lower final position) until the lower
and central bars remain lit in the lower final
position.
Now the installation mode has completed.
Precision adjustment of the upper and/or
lower final position:
After having set the lower final position, put the
door in the upper final position by briefly pressing
the UP button. The control unit switches off in
the final position set with the EES limit switch.
If you want to move the upper final position
upwards, it is necessary to set DIP switches 1, 2
and 4 on "ON" (to move it downwards, set DIP
switches 1, 3 and 4 on "ON").
A "0" appears on the display.
By briefly or repeatedly pressing the T2 button,
a correction factor falling between 1 and 9 steps
can now be set.
Then put all of the DIP switches on "OFF".
Now the final position has been corrected and
will be enabled with the next lifting. Now move
the door into the lower final position by pressing
the DOWN button.
The control unit switches off in the final position
set with the electronic limit switch.
If you want to move the lower final position
downwards, it is necessary to set DIP switches
1, 3 and 4 on "ON" (to move it upwards, set the
DIP switches 1, 2 and 4 on "ON").
A "0" appears on the display.
By briefly or repeatedly pressing the T2 button,
a correction factor falling between 1 and 9 steps
can now be set.
Then put all of the DIP switches on "OFF".
Now the final position has been corrected and
will be enabled with the next lowering.
This operation can be repeated several times
until the lower final position is perfectly adjusted.
English – 7