Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
1. List of contents
2. Special safety instructions
• Disconnect the battery from the charger base of the
grinder before changing any accessory, performing a
service or carrying out maintenance.
• Keep the machine and battery in a good condition.
Check the alignment of the moving parts on a regular
basis.
• Replace or repair damaged parts. Use an authorized
service agent and parts recommended by the
manufacturer. Non-authorized parts may be hazardous
and invalidate the guarantee.
• Before installing the battery, make sure that the
grinding machine is switched off.
• Keep the machine, battery and charger duly serviced
for a better and safer performance.
• Use suitable clothing for working. Never use neckties,
watches, rings and loose pieces of jewelry and remind
using a cap when necessary.
• Review your workplace and keep it orderly before
using the grinder.
• Check that the battery has been correctly inserted into
the handle of the machine.
• Make sure that the machine has no loose or wrongly
adjusted pieces, before turning it on.
• Avoid accidental starting; always keep the machine in
the "OFF" position.
• Protect your eyes with safety goggles (conventional
eye-glasses are not sufficient).
• Make sure that the floor is not slippery; use safety
shoes or boots.
• Take into account that this grinder must be connected
to the electric grid.
• Keep children and unauthorized persons out of the
working area.
• Do not use the machine where there are liquids, solids
or gases, such as solvents for paints, etc.
• Do not allow children to use the machine.
• Do not operate your grinder if any piece is lacking, as
this mat cause a failure and/or a possible injury.
• Do not hold the work piece in your hand without
protection (use gloves).
• Do not use the machine with your finger on the start
switch.
• Keep the button of the release trigger in its locked
position. Do not use the machine for jobs for which it
has been designed.
• Do not work with the grinder under the influence of
alcohol, drugs or inebriating medicaments.
ENGLISH
13
•
Do not wet the machine, battery or charger, and do not
use it in humid or wet areas. Keep the grinder, battery and
charger at a safe, dry, child-proof location, where the
temperature does not rise over 40ºC.
3. Instructions for start-up
Before adjusting or checking the tool, make sure that it is
switched off and that the battery has been extracted.
3.1. Placing or fixing the tool
Read these hazard alerts and instructions
entirely. If you do not comply with the following
hazard alerts and instructions, this may cause,
among other things, fire and/or severe injury.
Deploy the flap with the image of the apparatus and keep it
open while you are reading the handling instructions.
Regulatory use
The apparatus is aimed to cutting and grinding stone and
metal surfaces with an appropriate disk of a diameter of 115
mm.
Installation or extraction of the battery cartridge
Always switch off the tool before inserting or extracting the
battery cartridge.
To extract the battery cartridge, remove it from the tool at
the same time as sliding the buttons located at the sides of
the cartridge.
To insert the battery cartridge, align the flaps located at the
battery cartridge with the slot of the compartment and insert
it. Insert it completely until the gets firmly fastened and
becomes locked with a click. Otherwise, the cartridge may
accidentally get loose from the tool and cause injuries to the
user or any other person staying nearby.
• Do not force the battery cartridge to enter. If it does not
enter smoothly, this means that you are not installing it
correctly.
Shaft lock
(Figs, 3 - 4)
IMPORTANT! Never actuate the shaft lock 3 when the
shaft is moving, as otherwise the tool could get damaged.
When installing or extracting accessories, press the shaft
lock 3 to avoid the spindle 9 to rotate.
Operation of the switch
IMPORTANT! Before inserting the battery cartridge 2 into
the tool, always make sure that the sliding switch 1 works
properly, and that it returns to position "0" (Switched-Off)
when exerting pressure on the rear portion of the sliding
switch.
To start the machine, slide the sliding switch 1 to position "I"
(Switched-On).
For a continuous use, press the front portion of the sliding
switch 1 to lock it.
To stop the tool, press the rear portion of the sliding switch
and, thereafter, slide it to position "0" (Switched-Off).
13
(Fig. 1)
Publicidad
Capítulos
Tabla de contenido
