Assembling; Charger/Battery; Illustrated Description Of Functions; Operating Instructions - stayer AGL115 Manual De Instrucciones

3.2. Assembling

IMPORTANT! Always make sure to switch off the tool and
to extract the battery cartridge before trying to carry out any
kind of operation at the machine.
Installing the lateral grip
IMPORTANT! Before using the tool, always make sure that
the lateral grip is firmly installed.
Firmly screw the lateral grip 17 to the tool.
Installation or extraction of the disk guard
IMPORTANT! When suing a disk 10, the disk guard 6 must
be assembled to the tool in such a way that the closed side
of the guard always points towards the user.
Assemble the guard 6 such that the protuberance of the
guard neck stays aligned with the bearing housing.
Thereafter, turn the guard 180º.
Make sure that the screw 21 is well tightened.
To extract the guard 6, follow the installation process in
reverse order.
Installation or extraction of the grinding disk
(Figs. 3 - 4)
WARNING! Always use the guard 6 as delivered when the
grinding disk 10 is on the disk 10 may break during use and
the guard 6 helps reducing the possibilities of personal
injuries.
Assemble the internal flange 11 on the spindle 9. Fit the disk
10 on the internal flange 11 and screw the external flange
12 on the spindle 9.
Fit the disk in a secure and correct position, such that the
machine's direction of rotation coincides with that of the
disk according to the pointing arrows. On abrasive disks the
arrows are on the top side and visible to the user.
To tighten the external flange 12, exert pressure on the
shaft lock 3 so that the spindle 9 cannot rotate, and use the
wrench 14 for the external flange 12 so as to firmly adjust it
clockwise.
To extract the disk 10, follow the installation process in
reverse order.
WARNING! Never actuate the shaft lock the shaft is
moving.

3.3. Charger/battery

The SET is provided with two new lithium ion batteries 8
which arrive prepared ready to work; they must however
overcome a period of approximately 3 charges and
discharges, to achieve full performance.
IMPORTANT! When the battery 2 is new, it is sent in a low
charge condition. Charge the battery completely before
using your tool.
Assembly
To extract the battery from the machine, press the two
lateral stops 7 at the battery 2. Do not touch the metal
terminals. Take the charger base and connect it to the
electric grid.
(Figs.3-4)
(Figs. 5 a 8)
ENGLISH
14
The battery 2 is designed to fit in the charger 4 in a single
manner. This is to make sure that the positive (+) and
negative (-) polarities are in correspondence with each
other.
Insert the battery 2 and slightly press to set the battery 2
firmly in the charger base.
WARNING! Do not force the battery the other way round
into the base.

Operating instructions

Simply insert the battery 8 into the charger 4.
·When the charger 4 is plugged to the grid, the green LED
Ÿ
will flash.
·When the battery 8 is inserted into the charger, the red
Ÿ
LED will start to flash intermittently; this indicates that the
battery 2 is charging.
·When the red LED 18 stops flashing intermittently, it is
Ÿ
charged completely. (Fig.6)
·When, upon inserting the battery 8, the red LED 18 does
Ÿ
not turn on, the battery is completely charged.
To check the status of charge of the battery 8 by pressing
the button 19 at the upper portion of the battery 8, the lights
will flash to indicate the remaining charge in the battery.
WARNING! Once the tool turns off for a lack of charge,
do not keep pressing the On/off switch as this may
damage the battery.
IMPORTANT! If the light 18 starts flashing intermittently,
quickly after insertion of the battery, this may mean:
1) that the battery is too cold or too warm (the charger only
charges the batteries when their temperature is between
0ºC and 45ºC, the charger automatically (charge
maintenance mode)
Advice
- Do not charge at temperatures lower than 0ºC and higher
than 45ºC, as this may seriously damage the battery as well
as the charger.
- Do not remove the battery while a job is being carried out.
- If one foresees long periods of non-use of the tool, the best
is to disconnect the charger from the power supply.
- When the lithium ion battery is empty, the tool will turn off
automatically.
- A period of less work after a charges indicates that the
battery is worn out and must be replaced.

3.4. Illustrated description of functions

1. On/Off switch
1b. Lock button switch
2. Battery cartridge
3. Shaft lock
4. Charger
5. Green indicator light (battery charged)
14
(Fig. 1)