Additional Instructions - EINHELL Expert TE-XM 305 U Manual De Instrucciones

Anleitung_TE_XM_305_U_SPK8__ 26.09.12 16:31 Seite 42
GB
Do not remove any cutting residues or other parts
n
of workpieces from the cutting zone while the
machine is running and the saw unit is not at rest.
Make sure that the machine is always secured on
n
a workbench or a table if at all possible.
Support long workpieces (e.g. with a roller table)
n
to prevent them sagging at the end of a cut.

4. Additional instructions

Always pull the plug out of the power socket
n
before adjusting or servicing the machine.
Give these safety regulations to all persons who
n
work on the machine.
Do not use this saw to cut fire wood.
n
Caution! Hands and fingers may be injured on
n
the rotating saw blade.
Before you use the machine for the first time,
n
check that the voltage marked on the rating plate
is the same as your mains voltage.
If you need to use an extension cable, make sure
n
its conductor cross-section is big enough for the
sawʼs power consumption. Minimum cross-
section: 1.5 mm 2 .
If you use a cable reel, the complete cable has to
n
be pulled off the reel.
Never carry the saw by its cable.
n
Do not leave the saw in the rain and never use it
n
in damp or wet conditions.
Provide good lighting.
n
Never saw near combustible liquids or gases.
n
Wear suitable work clothes! Loose garments or
n
jewellery may become caught up in the rotating
saw blade.
Operators have to be at least 18 years of age.
n
Trainees of at least 16 years of age are allowed
to use the machine under supervision.
Keep children away from the machine when it is
n
connected to the power supply.
Check the power cable. Never use a faulty or
n
damaged power cable.
Keep your workplace clean of wood scrap and
n
any unnecessary objects.
Persons working on the machine should not be
n
distracted.
Note the direction of rotation of the motor and
n
saw blade.
After you have switched off the motor, never slow
n
down the saw blade by applying pressure to its
side.
Fit only blades which are well sharpened and
n
have no cracks or deformations.
42
The machine is to be operated only with tools
n
which conform with EN 847-1: 2003.
Faulty saw blades have to be replaced
n
immediately.
Never use saw blades which do not comply with
n
the data specified in this manual.
Make sure that the arrow on the saw blade
n
complies with the arrow marked on the machine.
Make certain that the saw blade does not touch
n
the rotary table in any setting. To do so, pull out
the power plug and tilt the saw blade by hand into
the 45° position and the 90° position.
If necessary, re-adjust the saw head as
described in Section C/F.
It is imperative to make sure that all the devices
n
used to cover the saw blade are in good working
order.
Never wedge the hinged guard hood in open
n
position.
Never dismantle the machineʼs safety devices or
n
put them out of operation.
Damaged or faulty safety devices have to be
n
replaced immediately.
Never cut workpieces which are too small to hold
n
securely in your hand.
Do not place your hands in awkward positions
n
where one or both may slip suddenly and touch
the saw blade.
When working with long workpieces, use an
n
additional support (table, stand, etc.) to prevent
the machine from tipping over.
Always clamp round workpieces such as dowel
n
rods etc. with suitable devices.
There must be no nails or other foreign bodies in
n
that part of the workpiece you want to cut.
Always stand to the side of the saw blade when
n
working with the saw.
Never load the machine so much that it cuts out.
n
Always press the workpiece firmly against the
n
table and the stop rail to prevent it from wobbling
or twisting.
Make sure that off-cuts can be removed from the
n
side of the saw blade. If not, they may catch on
the saw blade crown and be catapulted into the
surrounding area.
Never saw several workpieces simultaneously.
n
Never remove loose splinters, chips or jammed
n
pieces of wood when the saw blade is running.
To rectify faults or remove jammed pieces of
n
wood, always switch off the machine first. - Pull
out the power plug!
Conversions, adjustments, measurements and
n
cleaning jobs are to be performed only when the