Care & Cleaning; To Set Self-Clean - JENN-AIR JGR8880 Manual Del Usuario

C & C
ARE
Self-Clean Oven
CAUTION
• It is normal for parts of the oven to become hot during a
self-clean cycle.
• To prevent damage to oven door, do not attempt to open
the door when LOCK is displayed.
• Avoid touching door, window or oven vent area during a
clean cycle.
• Do not use commercial oven cleaners on the oven finish
or around any part of the oven. They will damage the
finish or parts.
The self-clean cycle uses above-normal cooking temperatures
to automatically clean the oven interior.
The oven should be cleaned regularly by wiping up spillovers
to prevent excessive smoke and flare-ups. Do not allow a
heavy build-up of soil to accumulate in the oven.
During the cleaning process, the kitchen should be well
ventilated to get rid of normal odors associated with cleaning.
Before Self-Cleaning
1. Turn off the oven light before cleaning. The oven light may
burn out during the clean cycle.
2. Remove broiler pan, all pans, and oven racks from the
oven. The oven racks will discolor and may not slide easily
after a self-clean cycle if they are
not removed.
3. Clean oven frame, door frame, area
outside of gasket, and around the
opening in the door gasket with a
nonabrasive cleaner such as Bon
Ami* or detergent and water. The
self-cleaning process does not clean these areas. They
should be cleaned to prevent soil from baking on during
the clean cycle. (The gasket is the seal around the oven
door and window.)
4. To prevent damage, do not clean or rub the gasket around
the oven door. The gasket is designed to seal in heat
during the clean cycle.
5. Wipe up excess grease or spill-overs from the oven
bottom. This prevents excessive smoking, flare-ups or
flaming during the clean cycle.
6. Wipe up sugary and acidic spillovers such as sweet
potatoes, tomato, or milk-based sauces. Porcelain enamel
is acid-resistant, not acid-proof. The porcelain finish may
discolor if acidic or sugary spills are not wiped up before a
self-clean cycle.
* Brand names for cleaning products are registered trademarks of the respective manufacturers.
LEANING

To set Self-Clean:

1. Press Clean pad.
2. REMOVE RACKS will be displayed. Remove the racks.
3. Select CONTINUE using the Quickset pad. The Quickset
pads are located on either side of the control panel display.
4. Set LIGHT soil level by entering 200 using the number pads
for two hours of cleaning time. Press the Enter pad.
OR
Select MEDIUM for a moderately soiled oven and three
hours of cleaning time.
OR
Select HEAVY for a heavily soiled oven and four hours of
cleaning time.
5. CLEAN, TIME, LOCKED and the cleaning time countdown
will be displayed while the oven is cleaning. OVEN
COOLING will appear in the display when the cleaning
time has been completed and the oven is still locked.
Important: The door lock will disengage approximately one
hour after the cleaning time is completed. OVEN COOLING
will go off in the display when the oven door has unlocked.
To Delay a Self-Clean Cycle:
1. Press Clean pad.
2. REMOVE RACKS will be displayed.
Remove the racks.
3. Select CONTINUE using the Quickset pad.
4. Set LIGHT soil level by entering 200 using the number
pads for two hours of cleaning time. Press the Enter pad.
OR
Select MEDIUM for a moderately soiled oven and three
hours of cleaning time.
OR
Select HEAVY for a heavily soiled oven and four hours of
cleaning time.
5. The door will lock. CLEAN, TIME, LOCKED and the
cleaning time countdown will be displayed
6. After door locks, press the More Options pad.
7. Select DELAY using the Quickset pad.
8. Select the number of hours you want to delay the start of the
self-clean cycle.
9. The delay time and cleaning time will be displayed.
5