Filling The Boiler During Use; Using Accessory For Cleaning Carpets; After Use - ARIETE 2706 Manual De Instrucciones

Insert the tank (G) by slightly pressing it downwards and at the same time pushing it inwards. Do not force the pin on the
upper side of the tank during its removal/insertion.
The appliance can be used with only the turbo brush or only steam, or by activating both vacuum/steam functions
at the same time. It is recommended to use the two functions separately by first removing the dust from the floor
and only afterwards activating the steam function.
using the turbo brush
Press button (O) to start the turbo brush (Fig. 9). The turbo brush will start to turn and together with the movement created
by the appliance, will collect the dust and small debris from the floor, putting it into the container (M).
Warning!
Do not turn the steam head upside-down to try to clean the turbo brush during use. Danger of becoming entangled
and pulled. Danger of the dust container falling.
Press the button (O) again to stop the turbo brush.
using the steam function
After use of the vacuum function, unplug the appliance. According to the kind of floor to be cleaned, choose the suitable cloth
(P-Q) and position it under the steam head (L) - Fig. 10. Lay the cloth on the apposite Velcro (V).
The cloth for delicate floors (Q) is suitable for parquet, wood, laminate.
The floor cloth (P) is suitable for tiles, terracotta tiles floor, stone, marble that require a deep cleaning.
Warning!
Make sure that the tank has been adequately filled to prevent dry operation.
To protect the floor from high temperatures, it is recommended to let the appliance heat or cool on the accessory
for carpet cleaning.
Before using the appliance be sure that the objects and surfaces to treat are resistant or compatible with the high
steam temperature. It is recommended to consult the manufacturer's instructions and perform a test on a concealed
part or a sample particularly on treated terracotta tiles and wooden surfaces.
If the appliance is left standing on the floor while it is in operation, you may notice a whitish ring. Do not be alarmed
because this can be removed with a decalcification agent or with some drops of vinegar.
Insert the plug into the socket, which must be earthed. The indicator lamp (D) will turn on, indicating that the appliance is
on and that the internal boiler is starting to heat up. Be sure to have first removed the dust from the floor. Run the appliance
over the floor after pushing the steam dispensing button (B).
Steam delivery can be adjusted through the apposite dial (F), by rotating it from a minimum (-) to a maximum level (+).
For more delicate floors, as parquet, wood or laminate, it is advisable to adjust steam delivery at a lower level, while, for sur-
faces requiring a deeper cleaning, e.g. marble, terracotta tiles floor, tiles or stone, it is advisable to adjust at a higher level.
Warning!
Do not use the steam function without the cloth. The cloth can be purchased at Authorised Service Centres.
Use the appliance in well-lit rooms.
Warning!
Danger of burns! Do not turn the steam head upside-down during use to remove the cloth.
Unplug it from the socket-outlet. Wait at least 5 minutes so that the steam head and cloth cool down.
You can remove the cloth during use to rinse it. Press the button (B) to stop steam dispensing before removing the cloth
and unplug it from the socket-outlet.

Filling the boiler during use

No special operation is necessary when the water in the tank runs out. Just unplug the machine, pull out the tank and fill it
with fresh cool water again. If the tap water is particularly hard (higher than 20°f), use a mixture of 50% tap water and 50%
demineralised water.

using accessory for cleaning carpets

The accessory must be used only to clean carpets and similar soft surfaces. Do not use on hard surfaces.
Lay the carpet attachment (S) on the floor on the flat side. Make sure the cloth is positioned underneath the steam head (L).
In case of carpets, use the floor cloth (P). Position the appliance on the attachment (S) by slightly pressing (Fig. 11). The
appliance is now ready for use.

After use

Remove the power cable from the socket-outlet. Empty the water tank completely so as to prevent the water from stagnat-
ing, which may form lime deposit.
13