Using The Tuner; Restoring The Factory Default Settings; Connecting To A Computer, Tablet, Etc - VOX Amplification Adio Air GT Manual De Usuario

Using the tuner

The built-in tuner function allows you to easily
tune the guitar connected to the INPUT jack.
Regular tuning mode
1.
Hold down the TAP button for about 1 second.
The tuner function turns on, and the
TAP/TUNER LEDs (red) light up.
When the tuner function has
been turned on, FX2 will be
bypassed.
2.
Play any open string on the guitar.
Be careful not to play any of the other strings.
3.
Roughly tune the string until the LED (BANK
or USER PROGRAMS 1 through 4) indicating
the string that was played lights up.
4.
While checking the TAP/TUNER LEDs, cor-
rectly tune the guitar.
Sharp
Slightly sharp
In tune
Slightly flat
Flat
5.
Press the TAP button to turn off the tuner function.
(LED turns off)
Half down tuning mode
When the tuning function has been turned on and
the TAP button is held down for at least 2 seconds,
the TAP/TUNER LEDs (red) blink, and the amp
enters half down tuning mode, where all strings
can be tuned one semitone lower.
♭ ♭ ♭ ♭
In this mode, when the 6th through 1st strings are E
D , G , B and E , they will appear to be in tune.
The operating procedure and LED indications are the
same as with the regular tuning mode.

Restoring the factory default settings

The procedure for restoring the amp to its factory
default settings is described below.
When this operation is done, all programs saved as
USER PROGRAMS as well as all settings, such as
audio equalizer settings stored from Tone Room
and Bluetooth pairing information, will be reset to
the factory defaults.
After performing this operation, be sure to also delete this
amp's information from the Bluetooth devices it was
paired with. In order to connect the amp and device again,
pairing must be performed again.
1.
Turn off the amp.
2.
While holding down the USER PROGRAMS 1 and
USER PROGRAMS 4 buttons, turn on the amp. After
the BANK and USER PROGRAMS LEDs blink, release
the pressed buttons.
If you decide to cancel initialization at this point,
Tip
press the TAP button. Otherwise, if the next step is
not performed within about 15 seconds, the amp
will return to normal operation without initializing.
3.
Hold down the BANK/MANUAL button until the
LEDs change from blinking to lit (at least 2 seconds).
Initialization begins, and the BANK and USER PRO-
GRAMS LEDs change from blinking to lit. Initializa-
tion is completed after about 1 to 2 seconds, and the
amp returns to normal operation.
Never turn off the amp while initialization is in
progress.

Connecting to a computer, tablet, etc.

Tip Download the newest versions of each driver and software from
the VOX website (www.voxamps.com).
Connecting to external devices via USB
By connecting a computer, tablet, smartphone, etc., using a
commercially available USB cable, the amp can be used as a USB
audio interface or the editor/librarian software "Tone Room"
can be used to manage programs and customize amps/effects.
In order to connect to an iOS device (iPad or iPhone), a
commercially available adapter, such as the Apple Light-
ning to USB camera adapter, will be required.
In order to connect to an Android device, a commercially
available USB On-The-Go (OTG) connector will be re-
quired. In addition, the Android device must be running
♭ ♭
Android 6.0 or later in order to use Tone Room.
, A ,
The input to the AUX IN jack is not output to the USB port.
Tip Install the VOX USB-MIDI Driver in order to use Tone
Room on a Windows or Mac computer connected via USB.
Tip The USB audio function operates with the driver included
with the operating system; however, if the VOX 2ch Audio
Driver is installed and an ASIO-compatible application is
used, recording and playback may be slightly delayed.
13