Publicidad
Idiomas disponibles
Idiomas disponibles
Modellbau Lindinger GmbH
• Seal the tube. 3.5 against water ingress on the inside of deck-
marked with arrow opposite.
The seat support framework, 3.11-3.17 will now be dry assembled.
• Fit former middle, 3.11 to the longitudinal formers, 3.13.
• Fit formers, 3.12, 3.14 and 3.15 from beneath.
• Fit screw guides, 3.16 from above and 3.17 from below. Slide
retaining bolt, 3.18 into the plate.
Stage 4
Part No. Description, size in mm
4.1
Cover, black, 1.5 Vac
4.2
Cover, black, 1.5 Vac
4.3
Cover retainer, 3 PP
4.4
Self tapping screw, D 2,2 x 9,5
4.5
Seat, black, 1,5, Vac
• Smooth all edges of deck openings with sand paper.
• Trim the edges of covers, 4.1 and 4.2 with modelling knife. Sand
edges and test fit in the openings in deck.
• Drill a D1, 5 mm hole at marked position. Attach cover retainer,
4.3 and tighten but allow the retainer to rotate. Fix screw from
underside of deck with some Stabilit-Express.
• Clip the seat support framework assembly, 3.11-3.18 into its
position in formers, 3.3/3.4. Tighten retaining bolt, 3.18 to fix in
place.
• Test fit seat, 4.5. Smooth edges of framework with a file/ sand-
paper to ensure a perfect fit of seat to deck.
• Retain seat framework to deck with pieces of adhesive tape laid
across the unit.
• Remove bolt, 3.18.
• Lay the seat on the deck and retain in place with self adhesive
tape.
Part No. Description, size in mm
4.6
Strengtheners, 3 PP
4.7
Handlebars, PM
4.8
Self tapping screw, D2 x 11
© robbe Modellsport
Alte-Post-Str. 14
Assembly and operating instructions
• Push a D4 drill through the press nut and drill a hole from the
underside through the seat unit.
• Carefully open up the hole to D6 using a step less drill, remove
seat unit.
• Fit bolt, 3.18 again to support frame and remove tape strips.
• Apply Stabilit-Express to the edges of the longitudinal, 3.13 and
other formers 3.14, 3.15, carefully set seat unit on the support
frame and adjust for best fit.
• Now reaffix the seat unit with clear tape. Turn the model over and
allow adhesive to harden thoroughly.
• Remove bolt, 3.18 through the D6 hole and remove seat unit.
number required
• Bond the strengtheners to the underside of the seat unit. Avoid
adhesive coming into contact with lug "H". This lug must sit flush
1
with the front edge of the seat unit.
1
1
• Drill the two D2 holes in the strengthener and fit the handlebars,
1
4.7 with the self-tapping screws, 4.8.
1
Part No. Description, size in mm
4.9
Mirror, PM
• Bond all the formers of the seat support framework together with
cyanoacrylate glue.
• Screw guide lower 3.17 must remain free of glue. If you ever
need to replace fixing bolt, 3.18, slide out 3.17 and remove 3.18.
• The lug "H" can now be removed- see detail illustration.
• Bond and adjust mirrors, 4.9 in place.
Stage 5
Part No. Description, size in mm
5.1
Hull
Installation of Drive Unit
Stabilit Express will be used for all joints
number required
• Place the drive unit sub assembly in the hull, 5.1.
1
• Set the rudder bearing, 2.9 in the hull such that it protrudes 0,5
1
mm from hull underside, do not bond.
2
A-4591 Molln
e-Mail: office@lindinger.at
Sea-Jet Evolution
number required
2
number required
1
4
www.lindinger.at
• Bond the motor former 1.1 und the rear edge of the servo tray,
1.12 into the hull. The servo tray may bend slightly when instal-
led in position.
• Do not bond latch plate 1.13 in place.
• Bond and seal the stuffing tubes to the hull, ensure the tubes
protrude 12 mm from rear of hull.
Part No. Description, size in mm
5.2
Lock nut, M4
5.3
Propeller, right + left
5.4
Hook and loop tape
• Cut the assembly lug from the motor former, 1.1.
• Screw the propellers, 5.3 and the lock nuts, 5.2 to propeller shaft.
Lock the propellers into place with the M4 lock nuts.
• Slide the rudder unit into the rudder bearing; refit O-ring 2.11 and
collet 2,12. Tighten and fix in place.
• Align rudder. The rudder must be vertically aligned when viewed
both from the rear and side. If necessary, you can adjust the hole
in the servo tray to adjust the guide until the fit is correct. When
all is correct, seal and bond the guide to the hull and servo tray
with Stabilit-Express.
• Lay battery tray in position in the hull. Bond formers 1.16-1.18 to
the hull but avoid getting glue into contact with the latch plate,
1.13.
• The plug-in stop plate, 1.19 remains loose and must not be fixed
in position.
• Finish off the installation of the radio system and install rudder
linkage between servo and rudder.
• Feed the hook and loop tape, 5.4 into position in the battery tray.
Bonding Deck to hull
• With deck unit upside down, apply a thin and even bead of adhe-
sive to the recess in the deck unit.
• Carefully position hull onto deck and remove excess glue that
may squeeze out of the joint.
• Now place the complete boat in its stand and clamp in place
whilst the adhesive dries. Be careful to make sure that the hull
sits square in the stand and that no stress or force is applied to
the deck whilst the adhesive cures.
No.
1266
number required
2
1 each
2
Publicidad
