Publicidad
Enlaces rápidos
Please Contact Moen First
For Installation Help, Missing or
Replacement Parts
(USA)
1-800-BUY-MOEN (1-800-289-6636)
Mon - Fri 8:00 AM to 8:00 PM, Eastern
Sat. 9:00 AM to 5:30 PM Eastern
WWW.MOEN.COM
(Canada)
1-800-465-6130
Mon - Fri 7:30 AM to 7:00 PM, Eastern
WWW.MOEN.CA
Por favor, contáctese primero
con Moen
Para obtener ayuda de instalación, piezas
faltantes o de recambio
01-800-718-4345
Lunes a viernes de 8:00 a 20:00 hs.
(Costa Este)
Sáb. 8:00 a 18:30 hs. (Costa Este)
WWW.MOEN.MX
Veuillez d'abord contacter Moen
en cas de problèmes avec l'installation, ou
pour obtenir toute pièce manquante ou de
rechange
1-800-465-6130
Du lundi au vendredi:
de 7 h 30 à 19 h, HE
WWW.MOEN.CA
Installation Guide
Guía de Instalación
Guide d'installation
TWO HANDLE LAVATORY FAUCET
ROBINET DE LAVABO À DEUX POIGNÉES
Images in this instruction sheet may not reflect your current product, but should follow the same step-by-step instructions.
Las imágenes en esta hoja de instrucciones pueden no reflejar su producto pero se debe seguir las mismas instrucciones de instalación paso a paso.
Il est possible que les images dans ce feuillet de directives ne reflètent pas votre produit actuel, mais les directives à suivre sont les mêmes.
INS2234- 10/13
INSXXX29 - 4/13
MEZCLADORA PARA LAVABO
DE DOS MANERALES
Publicidad
Manuales relacionados para Moen INS2234-10
Resumen de contenidos para Moen INS2234-10
- Página 1 INS2234- 10/13 INSXXX29 - 4/13 Installation Guide Please Contact Moen First Guía de Instalación For Installation Help, Missing or Replacement Parts (USA) Guide d’installation 1-800-BUY-MOEN (1-800-289-6636) Mon - Fri 8:00 AM to 8:00 PM, Eastern Sat. 9:00 AM to 5:30 PM Eastern WWW.MOEN.COM...
- Página 2 Open faucet han- HERRAMIENTAS ÚTILES dle to relieve water pressure and ensure that complete water Para que el cambio de la llave sea fácil y seguro, Moen le shut-off has been accomplished. recomienda usar estas útiles herramientas.
-
Página 3: Liste Des Pièces
INS2234- 10/13 Parts List A. Handles (2) B. Spout C. Valve Clips (2) D. Upper Mounting Washer (2) E. Lower Mounting Washer (2) F. Mounting Nuts (2) G. Cold Valve Body H. Mounting Bracket I. Bracket J. Spout Mounting Nut K. -
Página 4: Parts List
Parts List Plastic Waste R. Aerator Tool Desagüe de plástico S. Plug Bonde en plastique Lift Rod U. Pivot Rod Clip V. Waste Seat W. Drain Body X. Drain Nut Lift Rod Strap Z. Pivot Rod Seat AA. Pivot Rod Washer BB. - Página 5 INS2234- 10/13 Sealant Sellador Mastic Apply a small amount of silicone lubricant (M) to the black rubber o-ring on Apply a bead of plumbers putty or other sealant to the base of the spout s the spout shank (L) as shown. as shown.
- Página 6 Sealant Sellador Mastic Apply a generous bead of plumbers putty or other sealant to underside of Use mounting tool (O) to tighten the mounting nut (J) to the spout base (L). the upper mounting washers (D). A putty groove is provided for this purpose. Turn washers (D) over and position on sink as shown.
- Página 7 INS2234- 10/13 Slide clip (C) into the groove on each valve body. Check to see that each Hold valve body (N) with one wrench and tighten the lower mounting nut valve body outlet connection below the deck points towards the spout (F) using a 2nd wrench.
- Página 8 Position (A) with handles pointing in the off direction as shown. Holding the Rotate the red stem extension on the hot valve body (N) clockwise and the handle stationary with one hand, thread the base of the handle assembly (A)onto blue stem extension on the cold valve body (G) counterclockwise until the valve bodies (N&G) turning clockwise until (A) tightens to the deck.
- Página 9 INS2234- 10/13 SÍ Tighten drain nut (X) and drop plug (S) into waste seat (V) as shown. Rotate pivot rod opening on side of drain gasket (Z) to face towards wall as illustrated. Apriete la tuerca del desagüe (X) y deje caer el tapón (S) dentro del asiento Haga girar la abertura del pivote en el costado del empaque del desagüe (Z) del desagüe (V) como se muestra.
- Página 10 1.) Loosen nut on strap (Y) to allow lift rod to rest in faucet. 2.) Verify pivot Push pivot rod (CC) down. Insert pivot rod through closest hole on liftrod rod is still pushed down, and plug is open. 3) Tighten bolt with wrench. strap (Y) with pivot rod down.
- Página 11 INS2234- 10/13 Cold Frio Froid Caliente Chaud Place product ID label (Q) here. Coloque la etiqueta de identi cación del producto (Q) aquí. Placer l’étiquette d’identi cation du produit (Q) ici. To flush debris from the plumbing system: Remove the aerator by unthreading Turn hot and cold water stop valves to the on position.
- Página 12 Some states, provinces and nations do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state, province to province, nation to nation. Moen will advise you of the procedure to follow in mak- ing warranty claims.