Descargar Imprimir esta página

Fontanot arkè Karina Instrucciones Para El Ensamblaje página 6

Ocultar thumbs Ver también para arkè Karina:

Publicidad

Idiomas disponibles

Idiomas disponibles

English
WARNING: Carry out the installation in a "workmanlike" manner, strictly following the installation instructions
and using suitable tools. always consult your local building department for code requirements that must be
respected depending on its destination of use (private, secondary, public...).
Before starting the assembly process, unpack all components of the staircase. Lay them out on a large
surface and check the quantity of all the pieces, by consulting the table (TAB.1: A = Code, B = Quantity).
Inside the staircase box you will also find a DVD which we suggest watching before proceeding to assemble.
For customers in the USA there is a customer assistance number 1-888 STAIRKT, which you can telephone
in case of problems.
Assembly
1. Carefully measure the floor-to-floor height.
2. Calculate the rise:
1) subtract 22 cm (8
2) divide this value by the rises number minus one.
Example: for the measured floor-to-floor height of 268 cm (105 ½ " ) and a staircase with 12 rises;
(268 - 22) / (12 - 1) = 22,36
(105 ½ " - 8
" ) / (12 - 1) = 8
21
/
32
3. Determine the position of the support N19 (fig. 1) keeping in mind two points:
1) the rise, calculated previously, also contains the tread depth (L40) (fig. 2).
2) position the support N19 keeping in mind the opening feature (fig. 3).
4. Drill with the drill bit D. 14 mm (
5. Assemble on the floor, in a straight line, the supports N19, N18, N17 and N16 keeping in mind the
calculated rise. Use the parts C15, B71 and B75 (fig. 1). Tighten sufficiently keeping in mind that the
supports N19, N18, N17 and N16 still have to rotate for the configurations B, C, D.
6. Lift and position the structure with the support N19 which has to touch the floor (fig. 4). If the stair place
is too tight, it is suggested to rotate some supports.
7. Tighten the support N19 completely, by using the part C39 (fig. 1).
8. Determine at this point which is the first step from the top. Drill L40 treads using the cardboard cutout
jig L41 you find in the package, alternating a right tread and a left tread (fig. 3).
9. Cut along the shape (fig. 7 - center page).
10. Decide where to assemble the railing (inside or outside) (fig. 3) and pierce the treads (L40) with the drill
bit D. 6,5 mm (¼") usIng the template only for the straIght sIdes. To find the fixing point on the
short side of the winding treads (L40) maintain the same distance as the one between the balusters
(C12) to assemble on the long side of the tread (fig. 3).
11. Assemble and tighten the parts F23 by using the parts C14, B83, C49, C13, B02 (fig. 1).
12. Fasten element N26 to the treads L40 using the screw C57.
13. Finally attach the treads (L40) starting from the bottom N16 up to the support N19, using the elements
C57 (fig.1).
14. 1.The configuration A (straight) doesn't need any further changes (fig. 3).
2. The configurations B or C need a rotation of 13° (fig. 3).
3. The configuration D needs a rotation of 18° (fig. 3).
15. To rotate the supports of 13° or 18° you have to proceed as follows:
a. Set out with a pencil, at the connection point of two supports, two vertical lines at a distance of 9 mm
"
23
(
) (to rotate 13°, configuration B or C) (fig. 5) or 13 mm (
/
64
b. Loosen the parts C15, one support by one, starting from the top and rotate until one of the lines
matches the one of the top according to the direction of rotation.
c. Tighten the parts C15 completely (fig. 1).
Assembly of the Railing
16. Assemble the parts C28 by using the parts C13, B02 and insert them into the balusters (C12) (fig. 1).
17. Insert the balusters (C12) into the parts F23, blocking them by the part B02.
18. The first balusters (C12) of the long side of every tread (L40) have to be cut.
19. Tighten the part C28 completely, by using the part B02 (fig. 1). For a correct assembly twist the key at
" ) from the floor-to-floor height you measured,
21
/
32
" .
13
/
16
"
35
).
/
64
"
33
) (to rotate 18°, configuration D) (fig. 6).
/
64
6 - kr

Publicidad

loading