Testing The Code For Maximum Functionality; Auto Code Search And Entry - RCA NaviLight4 Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

RCR460_NA_IB_.qxd
3/2/06
Programming Methods (continued)
6. Press and release the ON·OFF key
repeatedly until your component turns
off. Each time you press the ON·OFF key,
the illuminated component name blinks,
and the next code in the list is sent. This
process continues until all of the codes in
the Code Lists have been searched. If
your component turns off, you have
found the correct code. (If it cycles
through and the illuminated component
(NAME BLINKS)
name blinks four times and turns off, all
codes have been searched. The Manual
Code Search method is exited.)
!
TIP
you may have to press the ON·OFF key
many times—possibly up to 200 times.
7. Once you have found the correct code,
you must save the new code by pressing
and releasing the STOP key. The
illuminated component name turns
off. You must press the STOP key to
(LIGHT OFF)
save the code or the correct code will
not be stored!
8. When you press the STOP key, the code
is stored.
9. Be sure to retrieve the code your remote
programmed by finishing the Code
Retrieval process found on page 10.

Testing the Code for Maximum Functionality

To confirm that the component key is programmed with the correct
code for maximum functionality, it is necessary to test the component.
If some of the features of your component do not work, different codes
in the list can be tried until you find the code that allows the remote to
control the majority of your component's functions. Different codes
can provide different levels of functionality. Follow these steps to test
for maximum functionality.
1. Once the code has been stored (see Manual Code Search and Entry
Method on page 6), use the remote to attempt to control a variety of
the component's functions. If the code that has been stored controls
the majority of the component's functions, programming
is complete. If the code stored does not give maximum
functionality, you will want to try another code.
2. In that case, repeat the Manual Code Search and Entry Method
from step 1. When the component turns off for the first time, do not
press the STOP key, which would store the code. Instead, with the
unit now off, continue to press the ON·OFF key repeatedly until the
unit turns back on. Once the unit turns back on, you have found
another code that operates the component. Press the STOP key.
3. Test the functionality again by attempting to control a variety of the
component's functions. If the code that has been stored controls the
majority of the component's functions, programming is complete. If
the code stored does not give maximum functionality, you will
want to try another code.
4. Repeat the Manual Code Search and Entry Method from step 1.
Each time a code turns the component on or off, you have found a
code that operates the remote and needs to be tested for maximum
functionality. Continue through the code lists, cycling through the
codes you have already tried, until you find one that offers
maximum functionality.

Auto Code Search and Entry

The Auto Code Search and Entry Method enables the remote to
automatically search through all the codes in the Code Lists for the
one that operates your component. Example used is for TV component
set up.
Note: The Auto Code Search method may take a long time because
the remote searches through all of the codes in its memory for the
code that operates your component. Therefore, if your brand is listed
in the Brand Codes or the Code Lists, first try the Brand Code Search
or the Direct Code Entry method described on pages 4-6.
8
9:50 AM
Page 8
Because there are so many codes,
!
TIP
To exit without saving at any point in the Auto
Code Search, press and release the GO BACK key.
1. Manually turn on the component you
want the remote to control (TV, VCR,
DVD, satellite receiver or cable box).
2. Press and hold the component key (TV,
DVD, VCR·AUX, SAT·CBL) you wish to
program. (To program the VCR·AUX key
(NAME
to control a component other than a VCR,
NOT LIT)
see page 7.) The illuminated component
name turns on and remains on.
3. While holding the component key down,
press and hold the ON·OFF key. The
(NAMES LIGHTS UP)
illuminated component name turns off.
4. After holding down both keys for three
seconds, all of the component names
illuminate and stay on.
(STAYS LIT)
5. Release both keys. The name of the current component remains lit,
while all other component names turn off.
Note: If you press an invalid key during the Auto Code Search,
the remote does not respond. If you do not press a valid Auto Code
Search key (TV, DVD, VCR·AUX, SAT·CBL, ON·OFF, GO BACK,
PLAY, REVERSE, STOP), the search times out after two minutes.
When the search times out, the illuminated component name blinks
four times and turns off. The last programmed code under that
component key is retained.
!
TIP
Throughout the programming of each key, be sure to keep the
remote pointed at the IR sensor of the component you are currently
programming the remote to control.
6. Press and release the PLAY key, then wait five seconds to see if
your component turns off. If your component does not respond,
continue to press the PLAY key every five seconds until your
component turns off. Each time you press the PLAY key, the
illuminated component name blinks and a block of 10 codes are
sent to your component. This process continues until all of the
codes in the Code Lists have been searched. (If your component has
not turned off after all codes have been searched, the illuminated
component name blinks four times and turns off. The Auto Code
Search Entry method is exited.)
7. When your component turns off, you
know the correct code is in the last block
of 10 codes sent. Press and release the
REVERSE key. Wait two seconds to see if
your component turns on again. If your
component does not respond, continue to
press the REVERSE key every two
seconds until your component turns on
again. This will isolate the correct code in
the last block of codes sent. Each time the
REVERSE key is pressed, the illuminated
component name blinks.
Note: If you accidentally press the
(NAME BLINKS)
REVERSE key after your component
responds, press and release the FORWARD
key. Then, wait two seconds to see if your
component turns off again.
8. Once your component turns on, you have
found the correct code. You must save
the new code by pressing and releasing
the STOP key. The illuminated
component name turns off. You must
press the STOP key to save the code or
the correct code will not be stored!
(LIGHT OFF)
9. When you press the STOP key, the code
is stored.
10.To confirm that the component key is programmed with the correct
code for maximum functionality, it is necessary to test the
component. If some of the features of your component do not work,
different codes in the list can be tried until you find the code that
allows the remote to control the majority of your component's
functions. See the section entitled "Testing the Code for Maximum
Functionality" on page 8 for more information.
9

Publicidad

Tabla de contenido

Solución de problemas

loading

Este manual también es adecuado para:

Rcr460

Tabla de contenido