Additional Safety Information; Important Safety Instructions For Battery Chargers - Porter & Cable PCC761 Manual De Instrucciones

AddITIONAL SAFETY INFORmATION

• Do not use Type 1 flat cut-off abrasive or
diamond wheels without proper guard.
WARNING:
personal hearing protection that
conforms to ANSI S12.6 (S3.19) during
use. Under some conditions and duration
of use, noise from this product may
contribute to hearing loss.
WARNING:
glasses. Everyday eyeglasses are NOT
safety glasses. Also use face or dust
mask if cutting operation is dusty.
ALWAYS WEAR CERTIFIED SAFETY
EQUIPMENT:
• ANSI Z87.1 eye protection (CAN/CSA Z94.3),
• ANSI S12.6 (S3.19) hearing protection,
• NIOSH/OSHA/MSHA respiratory protection.
WARNING:
power sanding, sawing, grinding,
drilling, and other construction activities
contains chemicals known to the state of
California to cause cancer, birth defects
or other reproductive harm. Some
examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement
and other masonry products, and
• arsenic and chromium from
chemically-treated lumber.
Your risk from these exposures varies,
depending on how often you do this type
of work. To reduce your exposure to these
chemicals: work in a well ventilated area,
and work with approved safety equipment,
such as those dust masks that are specially
designed to filter out microscopic particles.
• Avoid prolonged contact with dust
from power sanding, sawing, grinding,
drilling, and other construction
activities. Wear protective clothing
and wash exposed areas with soap
and water. Allowing dust to get into your
mouth, eyes, or lay on the skin may
promote absorption of harmful chemicals.
WARNING:
generate and/or disperse dust, which may
cause serious and permanent respiratory
or other injury. Always use NIOSH/OSHA
approved respiratory protection appropriate
for the dust exposure. Direct particles away
from face and body.
WARNING:
for long periods of time. Vibration
caused by the operating action of this
tool may cause permanent injury to
fingers, hands, and arms. Use gloves to
provide extra cushion, take frequent rest
periods, and limit daily time of use.
WARNING:
grinder on a stable surface where it will
not move inadvertently, roll or cause a
Always wear proper
ALWAYS use safety
Some dust created by
Use of this tool can
Do not operate this tool
When not in use, place
tripping or falling hazard. The grinder
may stand upright on the battery pack
but may be easily knocked over. Serious
personal injury may result.
CAUTION:
personal injury, use extra care when
working into a corner or edge because a
sudden, sharp movement of the tool may
be experienced when the wheel or other
accessory contacts a secondary surface
or a surface edge.
• When using an extension cord, be sure to
use one heavy enough to carry the current
your product will draw. An undersized cord
will cause a drop in line voltage resulting
in loss of power and overheating. The
following table shows the correct size
to use depending on cord length and
nameplate ampere rating. If in doubt, use
the next heavier gage. The smaller the
gage number, the heavier the cord.
Minimum Gauge for Cord Sets
Volts
120V 0-25
(0-7,6m) (7,6-15,2m) (15,2-30,4m) (30,4-45,7m)
Ampere Rating
More Not more
Than Than
6 - 10 18
SAVE ThESE INSTRUCTIONS
SYMBOLS
The label on your tool may include the
following symbols. The symbols and their
definitions are as follows:
V ..................volts
A ..................amperes
Hz ................hertz
W .................watts
min ..............minutes
...............alternating current
or DC ...direct current
n o ................no load speed
................Class I Construction
(grounded)
................earthing terminal
...............safety alert symbol
...........Class II Construction
(double insulated)
.../min or rpm...revolutions or
SPM ............Strokes per minute
5/8 -11 ............. Arbor size and Thread
............Read instruction manual before use
................Use proper eye protection
................Use proper hearing protection
................... Use proper respiratory protection
IMPORTANT SAFETY
INSTRUCTIONS FOR
BATTERY ChARGERS
SAVE ThESE INSTRUCTIONS: This
manual contains important safety
instructions for battery chargers.
6
To reduce the risk of
Total Length of Cord in Feet
26-50 51-100 101-150
American Wire Gauge
16 14 12
reciprocation per minute
count per inch