Installing The Hood - Fulgor Milano FDDH 900 TRC X Instrucciones Para La Instalación Y Uso

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

INSTALLING THE
COOKER HOOD
1. Before carrying out the appliance installa-
tion, please check that all components are
not damaged, in such a case contact your
retailer and do not carry out any installation
operation.
Before the installation of the Downdraft,
please remove the safety piece you can see
in the picture (Fig. 1). Furthermore, please
read carefully all of the following installation
instructions.
• Use an air exhausting pipe whose maxi-
mum length does not exceed 5 meters.
• Limit the number of elbows in the piping,
since each elbow reduces the air capac-
ity of 1 linear meter. (Ex. : if you use no. 2
x 90 ° elbows, the length of piping should
not exceed 3 meters).
• Avoid abrupt direction changes.,
• Use a 150 mm. constant diameter pipe
for the whole length.
• Use piping approved by standards in
force.
The manufacturer shall not be deemed re-
sponsible for air capacity or noise problems
caused by failure to comply with the above
instructions and no warranty on the product
shall be provided.
2. Before making the hole, check that there are
no structural or other parts inside the cabi-
net, where the appliance is to be placed,
which could hinder a proper installation.
Check that the dimensions of the Downdraft
and the ones of the cook top are compatible
with the cabinet so that the installation can
be carried out properly.
3. Make a rectangular opening, 842 x 100 mm
Make a rectangular opening, 842 x 100
in size, in the back of the cook top for the 90
mm in size, in the back of the cook top
cm model and 542 x 100 mm for the 60 cm
for the 90 cm model and 1095 x100 mm
model and 1142 x100 mm for the 120 cm
for the 112 cm model. In the version with
model. In the version with the motor already
the motor already installed, remove the
installed, remove the screws and the suc-
screws and the suc-tioning unit in order
tioning unit in order to insert the down-draft
to insert the down-draft in the hole made.
in the hole made.
S-DD2-L FLUSH TOP
EN
4. Put the Downdraft in the opening, inserting it
from above as shown in (Fig. 2).
5. Fix the downdraft inside the cabinet, using
the special fixing brackets supplied with the
product (Fig. 3).
Insert the brackets in the lower side of the
downdraft (Fig. 3), in such a way that there
is a 2 mm distance between the lower side
of bracket and the bottom of the cabinet
(Fig. 3).
This distance will allow the traction to be po-
sitioned downwards of the product, at the
moment of fixing, in order to have the stain-
less steel trim perfectly adhering with the
work surface. Before inserting the screws,
please make sure that the appliance is per-
fectly perpendicular with the work surface.
6. Once the installation is complete and after
connecting the appliance to the mains pow-
er, lift up the downdraft and remove the door
block (Fig. 4); then open the door (Fig. 5)
and fit the filters in place (Fig. 6). In the ver-
sion of the Downdraft equipped with internal
motor, install the power unit orienting the air
outlet to the desired position, either down-
wards or upwards (Fig. 7).
The motor can be installed either on the front
or rear side of the downdraft After having in-
stalled the motor, connect the air ducts.
7. For versions with external motor, place the
suctioning unit (external motor) in a suitable
area and fit the exhaust air flue as illustrated.
Then fit the air outlet ducts between the ex-
ternal motor and the downdraft. Select an air
outlet from the five possibilities (Fig. 9) and
fit the union supplied with the appliance.
8. Place the metal box with the electronic com-
ponents in an easily reachable area for even-
tual technical assistance operations. (Fig.
9), connecting the three connectors (9 pole
connector for the actuator control and the
safety control, 4 pole connector for neon
lamp turn on and push-button connector)
(Fig. 10).
20
17

Publicidad

Tabla de contenido
loading

Tabla de contenido