Listening To Ipod / Iphone - Lenco iPD-9000 DAB+ Manual De Instrucciones

IPD9000 DAB+_IB draft R03 (1).pdf IPD9000 DAB+_IB draft R03 (1).pdf
11. MODE / SCAN / P-MODE button ----- In Standby mode: Set clock and 12/24 hour format.
12. SLEEP button ----- Select the time duration of the sleep timer.
13. TONE button ----- For Bass and Treble settings
14. DISPLAY / RDS button ---- In DAB mode: Display DAB station information.
15. ID3 ON/OFF button ---- In CD mode: Enable / Disable ID3 function.
16. PGM / MEM / VIDEO ON/OFF button ----- Set CD program; Save DAB / FM radio preset station; Select
17. Battery Compartment ----- Located at the back of the remote control.
This model supports different iPod/iPhone models.
1. Insert your iPod/iPhone into the docking port by placing the connector on the bottom of the
iPod/iPhone onto connector in the docking bay.
Caution: Please be careful when seating the iPod/iPhone into the docking to avoid damaging the
30-pin connector on the iPod/iPhone or in the docking system.
2. Press the STANDBY
3. Press the FUNCTION button to select iPod/iPhone mode.
In iPod/iPhone mode:
- To start playback music, press the
- To pause the music, press the
- To resume music, press the
- You may rotate the VOLUME knob (from the main unit) or press the VOLUME +/- button
(from the remote control) to adjust the volume to a desired level.
Note: The volume level cannot be adjusted using the volume control on your iPod / iPhone after being
docked.
- During a song playback, press and hold the
search backward / forward.
- To skip to previous or next song, press and release the
- To turn off the unit, press the STANDBY
- When the unit is powered by external DC adaptor and once the iPod/iPhone connected to
the docking station, the unit recharges the iPod/iPhone battery.
- In the case your Apple device "Shake to Shuffle" function was set to "On", your iPod music
song recorded in a higher signal level and the unit is turned to maximum volume level then
the unit may vibrate by heavy bass music which might cause your iPod music skipping
songs. You may reduce the volume level or set the "Shake to Shuffle" function to "Off" from
the path " Settings \ iPod \ Music \ Shake to Shuffle " in your Apple device.
Video Out from the iPod / iPhone
1. You can connect this unit to a television or other video display that has composite video input.
2. Securely dock the iPod (with video) / iPhone.
3. Connect the yellow RCA cable to the rear RCA video jack on the unit.
4. Connect the other end of the yellow RCA cable to VIDEO IN of television or video display.
5. Press the FUNCTION button to select iPod/iPhone mode.
6. Select a movie from your iPod/iPhone menu.
Note:
For earlier iPod with video models (with click wheel):
(a) On the main menu choose video then select video setting.
(b) Set the TV Out section to "ON".
(c) Switch back to the movie library and ready for playback a movie of your choice.
For iPod Touch, iPhone:
TV OUT "ON" is automatically set so the TV OUT selection setting is not available for user to
change.
7. The movie will playback on the Apple device screen.
8. Press the VIDEO ON/OFF button which toggle between the video out "ON" (watch movie on TV) and
video out "OFF" (watch movie on Apple device screen).
2012-5-16 2012-5-16 21:31:24 21:27:51
In FM radio mode: Scan FM radio station.
In CD mode: Select CD play mode.
In FM radio mode: Display FM station RDS information.
video-out on/off in iPod/iPhone mode.

Listening to iPod / iPhone

button to turn on the unit and the power status indicator lights on.
button.
button again.
7
button once.
/ buttons to perform high speed
/
buttons.
button and the power status indicator will turn off.