Publicidad
Idiomas disponibles
Idiomas disponibles
Timer-function (optional)
The timer function is available in two types:
-Stand-alone-timer 1..99 min: Audible signal with timing. This
function can only be activated as long as no cooking zone is in
operation (all stages = 0). Is any cooking zone started with
operation (level >0) than the stand alone timer keeps in
operation. If the timer shall be used to cut off a cooking zone
(see cooking zone timer) then the control must first be switched
off (power sensor) and switched on again.
-Cooking zone timer 1..99 min: This function can only be
activated as long as a cooking is active (stage < 0; display dot).
Audible signal with timing, four cooking zones to be cut off are
freely programmable.
Setting a timer value:
By adjustment with the slider area.
Primarily the adjustment of the first digit takes place and
thereafter the adjustment of the second digit.
Within 10sec after the adjustment of the second digit the value
might be reset. (Illuminated display dot in the timer display and in
case of a cooking zone specific timer a blinking assigned LED).
In case of an active timer display the timer value may be set to
[0] directly by pressing [0] on the slider area (left side)
Switching of an active timer:
A timer can be switched of by setting its value to 0.
A stand alone timer can be switched of by a double actuation of
the power key "1".
Timer Stand-Alone:
If the control unit is switched on (all cooking zone displays show
[0]), the stand-alone timer may be activated by pressing the
timer select key. The timer display show "00". The decimal dot
on the timer display flashes. The timer is cut off after 10 sec
(black display) if no further settings are made. In case of a timer
value is set with no activation of a cooking zone within 10sec,
the cooking zone displays are cut off (interposing relays are also
cut off). Possible optic warnings for hot cooking zones [H] are
displayed permanently
As long as the timer is selected (display dot flashes for 10 sec) it
can be set. The setting range is 0 -99 minutes in single steps; by
Slider area.
Directly after the timer value is set countdown starts with the
last set value. The timer is deselected automatically after 10 sec
and the timer display indicates the timer value. After expiring of
the set time an acoustic signal is given and the timer display
flashes „00".
The acoustic signal is terminated
-after 2 min and/or
-by actuating any key.
Thereafter timer display stops blinking and extinguishes. Possible
optic warnings for hot cooking zones [H] are displayed
permanently
By pressing the ON/OFF key "1", the control unit may be
switched from „purely timer operation" to cooking zone at
any time -with or without an activated Stand-Alone timer -.
Switching back to TC active mode with an active
Stand-Alone timer the timer is selected first (decimal dot on
timer display flashes). After a cooking zone is
selected, the decimal dot disappears from the timer display and a
steady decimal dot on the cooking zone
display flashes on. When switching off the control unit by
ON/OFF key "1", the Stand-Alone timer – if still in
operation -is also switched off.
Cooking zone specific timer programming
Switching on the TC enables timer setting for dedicated cooking
zones.
By actuating a cooking zone (cooking zone stage > 0) followed
by selecting the timer display (within 10 sec) a timer value may
be assigned to the cooking zone as a cut-off function. The LED
around the timer "9" indicates which cooking zone the timer had
been activated for.
As soon as the timer is selected the according LED is blinking
and the dot in the timer display is flashing permanently. In case
of a cooking zone is selected thereafter, the dot extinguishes and
the LED stops blinking.
When switching from one cooking zone to another, the timer
display indicates the current timer value of the respective cooking
zone. Timer settings of other cooking zones stay active.
Further setting is like with the stand-alone timer
In case of more than one active timer the display indicates the
lowest timer value (after 10s deselection time).
After expiring of the set time an acoustic signal is given and the
timer display flashes „00". The related timer LED is blinking
synchronously. The programmed cooking zone is cut-off, a
permanent "0" is displayed and the cooking zone is selected
automatically. After 10 sec (deselection time) a permanent "H"
is displayed on a
„hot"cooking zone. Otherwise, the symbol "0" is indicated.
The acoustic signal and the blinking of the cooking zone timer Led
is terminated
- after 2 min and/or
- by actuating any key.
Thereafter timer display stops extinguishes and the cooking zone
stays unselected.
Behaviour of the cooking zone specific timer is similar to the
stand alone timer.
In case of a timer is programmed for a cooking zone the
operating time limitation is dependent of the timer value and not
of the standard table value.
Precautions
- when the hob is in use keep all magnetizable objects away
(credit cards, floppy disks, calculators and so on)
- do not use any alluminium foil or place any foodstuffs wrapped
in alluminium foil directly on the hob
- do not place any metal objects such as knives, forks, spoons
and lids on the hob surface as they will heat up
- when cooking in a non-stick pan without seasoning, do not
exceed 1-2 minutes' pre-heating time
- when cooking food that may easily stick, start at a low power
output level and then slowly increase while regularly stirring.
- after cooking is finished, switch off using the control provided
(turn down to "0"), and do not rely on the pan sensor
- If the surface of the hob is damaged, immediately disconnect
the appliance from the mains to prevent the possibility of electric
shock.
- Never use a steam cleaner to clean the hob.
- This appliance hood is not designed to be used by people
(including children) with reduced physical, sensorial or mental
capacity, or who lack experience or knowledge about it, unless
they have had supervision or instructions on how to use the hood
by someone who is responsible for their safety.
- Children must be supervised to ensure that they do not play
with the appliance.
Cooking vessels (Fig. 3)
- a magnet-attracting vessel may be a suitable vessel for
induction cooking
Publicidad
