SCHOLTES LTE S3 XL60HZ Instrucciones De Uso página 26

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Only run a soak program with half loads.
EN
To run programs 6, 7, 8, 9, 10
6, 7, 8, 9, 10
6, 7, 8, 9, 10
6, 7, 8, 9, 10 (see tab. 7-02), select the
6, 7, 8, 9, 10
required standard program (see programs 1, 2, 3, 4, 5 in
tab. 2-02a) and then press the supplementar
button
button
button (ref. 6 fig. 7-02).
button
button
After using the above tables to choose the most suitable
washing cycle, program the appliance.
After using the above table to choose the most suitable
washing cycle, program the appliance.
Before starting a washing program, make sure that:
The water supply tap is open.
There is regenerating salt in the water softener tank
(to add salt, see the instructions in the general
manual).
The correct amount of detergent has been added to
the dispenser (to add detergent, see the instructions
in the general manual).
The spray arms are able to rotate freely and without
obstruction.
The racks have been correctly loaded (see the
instructions in the general manual).
The dishwasher door is securely closed.
7.2.1 Switching on
Press on/off button (ref. 1 fig. 7-02) to start the
Then wait for one of the program indicator
dishwasher.
lights
lights
lights to turn on (ref. 2 fig. 7-02).
lights
lights
7.2.2 Selecting and starting the program
Press the program selection button (ref. 3 fig. 7-02)
several times until the indicator light corresponding to
the required program turns on (ref. 4 fig. 7-02);
if required, press the relative buttons to select any
complementary functions (e.g.: "half-load", "program
delay"; see para 7.2.7 "options");
close the door; the program will start after about 2
seconds and the relative indicator light will flash
throughout the cycle (program running signal).
If the door of the dishwasher has not been closed or has
been incorrectly closed, the washing cycle will not begin.
SUPPLEMENTARY PROGRAMS
The supplementary program button (ref. 5 fig. 7-02) adds
five extra programs to the ones that can be directly
selected with the program selection button. Press the
26
supplementar
supplementar
y pr
y pr
ogram
ogram
supplementary pr
supplementar
y program
y pr
ogram
ogram
program indicator
program indicator
program indicator
program indicator
button (the indicator light turns on) after selecting the
"main" program (see 1, 2, 3, 4, 5 in tab. 7-02a).
As the function is memorized, press the button again
(the indicator light turns off) if you wish to run one of the
5 main programs for the next cycle.
7.2.3 End of program
The end of the program is signaled by a short beep.
Additionally, the indicator light of the "normal" and
"strong" programs (marked "end") flash.
7.2.4 Interrupting a program
To interrupt the current program simply open the door of
the dishwasher; to restart the program, simply close the
door again. The program restarts from where it was
interrupted.
7.2.5 Changing the current program
To change the current program, simply open the door of
the dishwasher and select the new program. Close the
door to run the new program automatically.
7.2.6 Canceling the current program
To cancel the current program, open the door and
press and hold down the program selection button
(ref. 3 fig. 7-02) for a few seconds until the indicator
lights of the fourth and fifth programs turn on (ref. pr.
4, pr. 5 fig.7-03).
Close the door again.
After about 1 minute, the dishwasher terminates the
cycle and the indicator lights of the fourth and fifth
programs (ref. pr. 4, pr. 5 fig. 7-03) start flashing.
Fig. 7-03
7.2.7 Options
HALF-LOAD
This option is particularly suitable for reduced loads and
saves on water and electricity. Before selecting the half-
load wash option, open the dishwasher door and choose
the required washing program (see para 7.2 "Setting the
washing program and switching on and off").
The half-load wash cycle can be selected in two different
ways using the halfload wash
halfload wash
halfload wash
halfload wash button (ref. 8 fig. 7-02):
halfload wash
once
once
press the button once
once to select washing in the upper
once
rack.
rack.
rack.
rack. This is confirmed by the relative indicator light
rack.
(ref. 9a fig. 7-02);
upper
upper
upper
upper

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Lfd s3 xl60hz

Tabla de contenido