Changing The Settings - Kärcher RDS1 SB-C Manual Del Usuario

xxxxxxxxxxxxxx Freely selectable text.
Can be entered with
the modem software
HSComm. 20 charac-
ters maximum.
F:222=MP Error message (ex-
pump WW ample)
.
.
.
F:224=Fuse Error message (ex-
burner ample)
Note
If there is no display text in the country's
language, only the error code /F:XXX) will
be sent.
If the system is locked due to an error, the
message will have this note in the second
line:
Unit disabled
Note
RDS1 sends the following message after
all errors have been rectified:
xxxxxxxxxxxxxx
No faults
Error messages
The meaning of the error messages is de-
scribed in the operating instructions manu-
al of the washing unit or the water
preparation.

Changing the settings

You need a PC to modify the settings. The
enclosed configuration software from IN-
SYS should be installed on the PC.
Changing the mobile services pro-
vider
Note
Before changing, check whether the de-
sired mobile network is available where the
plant/system is installed.
Keep the SIM card and the corresponding
PIN number ready.
Only SIM cards with 3V power supply may
be used. The voltage details are printed on
the SIM card.
For prepaid cards, ensure that you have
enough balance on the card.
 Switch off the RDS1 switch.
 Press release button of the SIM card
holder.
 Take out the SIM card holder.
 Remove the SIM card from the card
holder.
 Re-insert the SIM card holder.
 Disconnect serial cable between GSM
modem and control at the controls and
connect it to the PC.
 Switch on RDS1 switch - the GSM mo-
dem will be initialised:
The "Connect" LED glows for approx. 4
seconds.
- after another 8 seconds the LED sta-
tus starts to blink for approx. 20 sec-
onds
The "Signal" LED displays the strength
of the reception signal. Faster the LED
blinks, so much better is the reception.
 Start the configuration software
"HSCom" on the PC.
The programme automatially establish-
es the link to the GSM modem.
1 "New PIN" checkbox
2 "Basic Settings" tab
3 PIN input field
4 Input field: Service Centre Number
5 "Synchronise RS232" button
6 "Send values" button
7 "Read settings" button
Note
If the message "Monitoring time expired" is
displayed, it means the connection cannot
be established automatically. In such a
case, click the "Synchronise RS232" button
followed by the "Read settings" button in
the screen. This process can take approx-
imately 1 minute. Repeat the process if er-
ror messages are displayed.
 Activate the Basic Settings tab.
 Activate the "New PIN" checkbox.
 Enter the new PIN for the SIM Card in
the PIN input field.
 Enter the Service Centre Number of the
mobile operator in the Service Center
Number field.
Note
The Service Centre Number is needed for
sending SMS and can be found in the doc-
uments of the mobile phone operator.
Some Service Centre numbers are given in
the appendix to the manual of the GSM mo-
dem.
 Click "Send values" button
Note
Repeat the process if error messages are
displayed.
The new PIN is stored in the GSM modem
and is used for logging on to the GSM net-
work during every fresh start.
 Exit the configuration program on the
PC.
 Switch off the RDS1 switch.
 Press release button of the SIM card
holder.
2
-
EN
 Take out the SIM card holder.
 Place the new SIM card in the card
holder.
 Re-insert the card holder with SIM card
- the contacts of the SIM card must
point towards the left.
 Disconnect serial cable at PC and con-
nect it to the controls of the SB washing
unit.
 Switch on the RDS1 switch - the initiali-
sation process will be run.
The initialization process is completed
after approx. 90 seconds.
The "Power" and "Status" LEDs start to
glow.
The "Signal" LED displays the strength
of the reception signal. Faster the LED
blinks, so much better is the reception.
Change the receiver of messages
 Switch off the RDS1 switch.
 Disconnect serial cable between GSM
modem and control at the controls and
connect it to the PC.
 Switch on RDS1 switch - the GSM mo-
dem will be initialised:
The "Connect" LED glows for approx. 4
seconds.
- after another 8 seconds the LED sta-
tus starts to blink for approx. 20 sec-
onds
The "Signal" LED displays the strength
of the reception signal. Faster the LED
blinks, so much better is the reception.
 Start the configuration software
"HSCom" on the PC.
The programme automatially establish-
es the link to the GSM modem.
Note
If the message "Monitoring time expired" is
displayed, it means the connection cannot
be established automatically. In such a
case, click the "Synchronise RS232" button
followed by the "Read settings" button in
the screen. This process can take approx-
imately 1 minute. Repeat the process if er-
ror messages are displayed.
 Click "Alarm/Switch1" tab; you can now
modify the settings given below it.
7