Youwill Need; Electrical Requirements; Tools And Parts - Whirlpool CABRIO WTW6200SW2 Manual De Uso Y Cuidado

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Selecting theproper location f oryour w asher improves
performance
andminimizes noise a ndpossible washer "walk."
Your washer canbeinstalled inabasement, laundry room,
closet, orrecessed area. See "Drain S ystem."
IMPORTANT:
Donotinstall orstore thewasher where i twill b e
exposed totheweather.
Proper installation isyour r esponsibility.
Youwill need:
• Awater h eater settodeliver 120°F ( 49°C) water t othe
washer.
• Agrounded electrical outlet l ocated w ithin 4 ft (1.2 m)of
where t hepower cordisattached totheback ofthewasher.
See "Electrical Requirements."
• Hotandcold water f aucets l ocated w ithin 3 ft (90cm) o fthe
hotand coldwater f illvalves, andwater p ressure of
20-100 p si(138-690 kPa) forbest p erformance.
• Alevel floor w itha maximum s lope of1"(2.5 cm) u nder entire
washer. Installing thewasher oncarpeting isnot
recommended.
• Asturdy f loortosupport thewasher weight (washer, water
andload) o f315Ibs(143 kgs).
Donotstore oroperate y our w asher intemperatures
atorbelow
32°F (0°C). Some water c anremain i nthewasher andcancause
damage inlowtemperatures.
See "Washer Care" f orwinterizing
information.
Installation
spacing for recessed
area and closet
installations
The following spacing dimensions are recommended
for this
washer. This washer has been tested for installation with spacing
of 0" (0 cm) clearance on the sides. Recommended
spacing
should be considered for the following reasons:
Additional spacing should be considered for ease of
installation and servicing.
Additional spacing should be considered on all sides of the
washer to reduce noise transfer.
For closet installation with a door, minimum ventilation
openings in the top and bottom of the door are required.
Louvered doors with equivalent ventilation openings are
acceptable.
Companion appliance spacing should also be considered.
__
3"*
(7.6 cm}
n
olo
(310 crl _) _ "
1
.2,
24 I1,_ __
155 cr_ )
_"_ *-_7'/_"m-_-_
_" _ _"*1-- 27" ÷i 6'L--1÷
(2.5 cm)
(69.9 cm}
(2.5 cm}(2,5 crn} (68.6 cm} (12,7 cm}
A
B
_J_
3 _*
(7.6cm)
7
A. Front view
B. Side view
C. Closet door with vents
*Required spacing
The washer can be installed using the standpipe drain system
(floor or wall), the laundry tub drain system, or the floor drain
system. Select the drain hose installation method you need. See
"Tools and Parts."
Standpipe
drain system--wall
or floor (views A & B)
The standpipe drain requires a minimum diameter standpipe of
2" (5 cm). The minimum carry-away capacity can be no less than
17 gal. (64 L) per minute. A 2" (5 cm) diameter to 1" (2.5 cm)
diameter standpipe adapter kit is available. See "Tools and
Parts."
The top of the standpipe must be at least 39" (99 cm) high and no
higher than 96" (244 cm) from the bottom of the washer.
39 _
(gecm)
A
Laundry tub drain system (view C)
The laundry tub needs a minimum 20 gal. (76 L) capacity. The top
of the laundry tub must be at least 39" (99 cm) above the floor
and no higher than 96" (244 cm) from the bottom of the washer.
Floor drain system
(view D)
The floor drain system requires a siphon break that may be
purchased separately. See "Tools and Parts."
The siphon break must be a minimum of 28" (71 cm) from the
bottom of the washer. Additional hoses might be needed.
D

Hide quick links:

Publicidad

Tabla de contenido

Solución de problemas

loading

Tabla de contenido