Description; Tool Status Lights; Specifications - RIDGID RE 600 Serie Manual De Instrucciones

RE 6/RE 60/RE 600 Electrical Tools
Green
Red
Yellow
Figure 6 – Tool Status Lights

Specifications

*
With 2 Ah Battery
Figure 7 – Specification Chart
Piston Force ...............60 kN (6-ton) (13,500 lbs.)
QCS Coupling Type ...RE 6
Duty Cycle..................
Motor
Voltage ...................18V DC
Amperage ...............18 Amp
Power .....................324 Watts
Battery........................18V Li-Ion, Rechargeable Batter y
Ingress Protection .......IP32
Allowable Humidity......0-80%
6
Find Quality Products Online at:
Solid Light
Icon
Green
Red
Yellow
Model

Description

RE 6 6T Tool For Use
w/Interchangeable Heads
RE 60 60 kN Tool For Use
w/Interchangeable Heads
RE 600 RDH Latching Round
RE 600 SC Scissor Cut
RE 600 4PI 4 PIN Indenter
*
1
Includes dies
6T QCS
RE 60 60 kN QCS
RE 600 Series – N/A
3 Cycles per minute
(see Optional Equipment)
GlobalTestSupply
www.
Blinking Light
Meaning
Tool ON, ready to use.
Green Battery low. Tool will not operate. Recharge
battery/Insert fully charged battery.
Tool out of Specification temperature range. Bring tool
and battery to correct operating temperature range.
Indicates service interval approaching. Starts 2,000
Yellow
cycles prior to service interval (see Figure 7). Tool is
usable, but tool will lock after service interval.
Tool is locked. Tool has completed service interval
(see Figure 7) and requires service.
Tool has malfunctioned. Have serviced.
Weight *
g lbs
3000 6.6
3000 6.6
4300* 9.5
1
Die Head
4800 10.5
Head* 2
5300 11.7
Head
*
2
Versions for Cu/Al wire and ACSR available - See blade markings.
Operating Temperature
Range ...........................15° F to 122° F (-10° C to 50° C)
Storage Temperature
Range ...........................32° F to 113° F (0° C to 45° C)
Sound Pressure (L
Sound Power (L
Vibration .......................<2.5 m/s
*
* Sound and Vibration measurements are measured in accordance with a stan-
dardized test per Standard EN 62481-1.
- Vibration levels may be used for comparison with other tools and for pre-
liminary assessment of exposure.
- Sound and vibration emissions may vary due to your location and specific use
of these tools.
- Daily exposure levels for sound and vibration need to be evaluated for each
application and appropriate safety measures taken when needed. Evaluation
of exposure levels should consider the time a tool is switched off and not in
use. This may significantly reduce the exposure level over the total working
period.
Dimensions Piston Travel
L x H x W (mm)
mm inch
L x H x W (inch)
318 x 154 x 73 32 1.3
12.5 x 6.1 x 2.9
318 x 154 x 73 32 1.3
12.5 x 6.1 x 2.9
395 x 165 x 73 17 0.7
15.6 x 6.5 x 2.9
473 x 174 x 73 24 0.9
18.6 x 6.9 x 2.9
474 x 192 x 73 32 1.3
18.7 x 7.6 x 2.9
)* ...65 dB(A), K=3
PA
)*.......76 dB(A), K=3
WA
2 , K=1.5
999-999-463.10_REV. H
.com
sales@GlobalTestSupply.com
Service
Interval
Cycles
32,000
32,000
32,000
32,000
32,000