Product Description And Specifications - Bosch PLL 360 Instrucciones De Seguridad Y Manual De Instrucciones

OBJ_BUCH-979-006.book Page 10 Wednesday, July 13, 2016 6:22 PM
10 | English
Product Description and
Specifications
Intended Use
The measuring tool is intended for determining and checking
horizontal and vertical lines.
The measuring tool is suitable exclusively for operation in
enclosed working sites.
Product Features
The numbering of the product features shown refers to the
illustration of the measuring tool on the graphic page.
1 Exit opening for laser beam
2 On/Off switch
3 Tripod mount 1/4"
4 Laser warning label
5 Battery lid
6 Latch of battery lid
7 Button for switching off the automatic levelling
8 Operating mode button
9 Levelling warning indicator
10 Operating-mode indication
11 Working without automatic levelling indicator
12 Universal holder*
13 Rotary knob of the universal holder
14 Holding plate of the universal holder
15 Base plate of the universal holder
16 1/4" screw of the universal holder
17 Tripod*
18 Protective pouch
19 Laser viewing glasses*
20 Serial number
* The accessories illustrated or described are not included as
standard delivery.
Technical Data
Cross-line Laser
Article number
Working range (diameter),
1)
to approx.
Levelling Accuracy
Self-levelling range, typically
Levelling duration, typically
Divergence
– Laser Point
Operating temperature
Storage temperature
Relative air humidity, max.
1) The working range can be decreased by unfavourable environmental
conditions (e.g. direct sun irradiation).
Please observe the article number on the type plate of your measuring
tool. The trade names of the individual measuring tools may vary.
The measuring tool can be clearly identified with the serial number 20
on the type plate.
1 609 92A 1Y9 | (13.7.16)
Cross-line Laser
Laser class
Laser type
C
6
Tripod mount
Batteries
Rechargeable batteries
Operating time, approx.
Weight according to
EPTA-Procedure 01:2014
Dimensions
1) The working range can be decreased by unfavourable environmental
conditions (e.g. direct sun irradiation).
Please observe the article number on the type plate of your measuring
tool. The trade names of the individual measuring tools may vary.
The measuring tool can be clearly identified with the serial number 20
on the type plate.
Assembly
Inserting/Replacing the Batteries
Using alkali-manganese or rechargeable batteries is recom-
mended for operation of the measuring tool.
To open the battery lid 5, press on the latch 6 and fold the bat-
tery lid up. Insert the batteries/rechargeable batteries. When
inserting, pay attention to the correct polarity according to
the representation on the inside of the battery lid.
Always replace all batteries/rechargeable batteries at the
same time. Do not use different brands or types of batter-
ies/rechargeable batteries together.
 Remove the batteries/rechargeable batteries from the
measuring tool when not using it for longer periods.
When storing for longer periods, the batteries/rechargea-
ble batteries can corrode and self-discharge.
Operation
PLL 360
3 603 F63 000
Initial Operation
 Protect the measuring tool against moisture and direct
20 m
sun light.
±0.4 mm/m
 Do not subject the measuring tool to extreme tempera-
±4°
tures or variations in temperature. As an example, do
not leave it in vehicles for a long time. In case of large vari-
4 s
ations in temperature, allow the measuring tool to adjust to
the ambient temperature before putting it into operation.
0.5 mrad (full angle)
In case of extreme temperatures or variations in tempera-
+5 °C ... +40 °C
ture, the accuracy of the measuring tool can be impaired.
–20 °C ... +70 °C
 Avoid heavy impact to or falling down of the measuring
90 %
tool. Damage to the measuring tool can impair its accura-
cy. After heavy impact or shock, compare the laser line
with a known horizontal or vertical reference line.
 Switch the measuring tool off during transport. When
switching off, the levelling unit, which can be damaged in
case of intense movement, is locked.
PLL 360
2
635 nm, <1 mW
1
1/4"
4 x 1.5 V LR6 (AA)
4 x 1.2 V HR6 (AA)
12 h
0.38 kg
125 x 85 x 70 mm
Bosch Power Tools