mundoclima MUCOR-60-H8T Manual De Instalación Y Usuario página 63

REMOTE CONTROLLER
Operation of buttons
1 ON/OFF
2
MODE
3
FAN
4
5
ON/OFF Button
1
This button turns the air conditioner ON
and OFF.
MODE Button
2
Press this button to modify the air conditioner
mode in a sequence of following:
AUTO
3
FAN Button
Used to select the fan speed in four steps:
AUTO
NOTE: You can not switch the fan speed in
AUTO or DRY mode.
4
SLEEP Button
Active/Disable sleep function. It can
maintain the most comfortable temperature
and save energy. This function is available
on COOL, HEAT or AUTO mode only .
For the detail, see sleep operation in
,
, ,
USER S MANUAL.
NOTE: While the unit is running under SLEEP
mode, it would be cancelled if MODE, FAN
SPEED or ON/OFF button is pressed.
TURBO Button
5
Active/Disable Turbo function. Turbo function
enables the unit to reach the preset temper-
ature at cooling or heating operation in the
shortest time(if the indoor unit does not
support this function, there is no
corresponding operation happened when
pressing this button.)
6
7
SHORT
CUT
8
TIMER
ON
TEMP
TIMER 9
OFF
10
SLEEP
11
LED
TURBO
12
HEAT
COOL DRY
FAN
LOW MED HIGH
, , ,,
,,
6
UP Button( )
Push this button to increase the indoor
temperature setting in 1 C increments to 30 C.
DOWN Button(
Push this button to decrease the indoor
temperature setting in 1 C increments to 17 C.
NOTE Temperature contol is not available
in Fan mode.
7
SHORTCUT Button
Used to restore the current settings or
resume previous settings.
On the first time connecting to the power,
if push the SHORTCUT button, the unit
will operate on AUTO mode, 26 C, and fan
speed is Auto.
Push this button when remote controller is
on, the system will automatically revert
back to the previous settings including
operating mode, setting temperature, fan
speed level and sleep feature(if activated).
If pushing more than 2 seconds, the system
will automatically restore the current
operation settings including operating mode,
setting temperature, fan speed level and
sleep feature(if activated ).
8
TIMER ON Button
Press this button to initiate the auto-on
time sequence. Each press will increase
the auto-timed setting in 30 minutes
increments. When the setting time displays
10.0, each press will increase the auto-
timed setting 60 minutes increments.
To cancel the auto-timed program, simply
adjust the auto-on time to 0.0.
9
TIMER OFF Button
Press this button to initiate the auto-off time
sequence. Each press will increase the auto
-timed setting in 30 minutes increments.
When the setting time displays 10.0, each
press will increase the auto-timed setting
60 minutes increments. To cancel the auto-
timed program, simply adjust the auto-off
time to 0.0
10 Swing Button
Used to stop or start vertical louver movement
and set the desired left/right air flow direction.
The vertical louver changes 6 degree in angle
for each press. And the temperature display
area of indoor unit displays
second. If keep pushing more than 2 seconds,
the vertical louver swing feature is activated.
, And the display area of indoor unit displays
,
, flashes four times, then the tempera-
IIII
ture setting reverts back. If the vertical louver
swing feature is stopped, it displays LC and
remains on for 3 seconds.
NOTE: For some units , the indoor units
,
,
display when the swing feature is
activated, and display
swing feature is stopped.
Swing Button
11
Used to stop or start horizontal louver move-
ment or set the desired up/down air flow
direction. The louver changes 6 degree in
angle for each press. If keep pushing more
than 2 seconds, the louver will swing up and
down automatically.
12
LED Button
Disable/Active indoor screen Display. When
pushing the button, the indoor screen display
is cleared, press it again to light the display.
63
o o
)
o o
O
,
,
for one
, ,
, ,
when the