Product Specifications; Troubleshooting Guide; Warranty Information - BriskHeat SpeedTrace Extreme FFSL81-6 Manual De Instrucciones

WARNING
Fire and shock hazard. Damaged heating cable can cause electrical shock, arcing, and fire. Do
not attempt to repair or energize damaged heating cable. Remove it at once and replace with a
new length.

PRODUCT SPECIFICATIONS

Cable
Cable Cable
Length
(120V) (230V)
(feet)
FFSL81-6 FFSL82-6 6
FFSL81-12 FFSL82-12 12
FFSL81-18 FFSL82-18 18
FFSL81-24 FFSL82-24 24
FFSL81-50 FFSL82-50 50
FFSL81-75 FFSL82-75 75
FFSL81-100 FFSL82-100 100
General Specifications for all FFSL8 Products
Nominal cable width (in)
Nominal cable thickness (in)
Heating cable bus wire gauge (AWG)
Cold lead length (in)
Voltage rating (120V)
Voltage rating (230V)
Plug rating (amps)
Circuit breaker sizing minimum (amps)
Max. exposure temperature
Electrical classification
Exposure to chemicals
Watts/foot at 50°F (10°C)
Watts/foot at 32°F (0°C) in ice and snow
Outer Jacket Type
®
© BriskHeat Corporation. All rights reserved.
SpeedTrace Extreme Self-Regulating
Heating Cable
Min. power output Nominal power output
at 50°F (10°C) at 32°F (0°C)
on pipe (watts) in ice and snow (watts)
48 96
96 192
144 288
192 384
400 800
600 1,200
800 1,600
0.42
0.22
16
30
110-120
208-277
15
15
150°F (65°C)
Nonhazardous areas only
None
8
16
Moisture and flame resistant
thermoplastic elastomer
11

TROUBLESHOOTING GUIDE

Please read this guide prior to contacting BriskHeat
commonly asked questions. If you are unable to identify the problem or need additional
assistance, please contact your local distributor/ representative or us at 1-800-848-7673,
614-294-3376, or bhtsales1@briskheat.com.
PROBLEM
Entire heating cable does not heat
Portion of heating cable does not heat
Circuit breaker is tripping

WARRANTY INFORMATION

BriskHeat warrants to the original purchaser of this product for the period of eighteen (18) months
from date of shipment or twelve (12) months from date of installation, whichever comes
first. BriskHeat's obligation and the exclusive remedy under this warranty shall be limited to the
repair or replacement, at BriskHeat's option, of any parts of the product which may prove
defective under prescribed use and service following BriskHeat's examination, is determined by
BriskHeat to be defective. The complete details of the warranty can be found online at
www.briskheat.com or by contacting us at 1-800-848-7673 (toll free, U.S. / Canada) or
1-614-294-3376 (Worldwide).
4800 Hilton Corporate Dr. Columbus, OH 43232
Toll Free: 800-848-7673
Phone: 614-294-3376
Fax: 614-294-3807
Email: bhtsales1@briskheat.com
®
© BriskHeat Corporation. All rights reserved.
SpeedTrace Extreme Self-Regulating
Heating Cable
®
. This guide is designed to answer the most
SOLUTION(S)
Verify heater is connected to proper voltage.
Check to see if there is a resistance reading (not
an open circuit) in heater using an ohm meter.
Examine unheated cable for damage.
Validate that the circuit breaker is capable of
handling the amp requirement of heater.
Examine heater and cord for any damage.
12