V2 VEO-RFE Serie Manual Del Usuario página 15

CODE
FUNCTION
A B C
Storage of the transmitters and selection of the
12 11 11
mode awning
Storage of the transmitters and selection of the
12 11 12
mode rolling shutter
12 11 13 Deletion of all the stored transmitters
Programming of the upper position of
12 11 14
end-of-stroke sensor
Programming of the lower position of the
12 11 15
end-of-stroke sensor
Programming of the middle position of the
12 11 16
end-of-stroke sensor
A: Code to activate programming
B: Indicates channel 1 of the remote control; for channel 2 the number
is 12, for channel 3 the number is 13, etc. up to channel 6
C: Code of the function to be programmed
The pictures that follow include references to the buttons and the
LEDs used during programming.
Storage of the transmitters and selection of
the mode awning
To store a transmitter TX1 on a blank control unit proceed as
follows:
WARNING: the first transmitter stored fixes the direction of
motion of the motor.
1. Supply power only to the motor to be programmed
2. Activate ADLER programming by holding down buttons 4 and
6 until the 6 LEDs turn on
3. Release the buttons and enter the code 12 11 11
The two highlighted digits indicate the remote control channel
to be recorded; for channel 1 the digits are 11, for channel 2
the digits are 12, for channel 3 the digits are 13, etc up to
channel 6. Once the codes have been entered, the LED of the
selected channel will blink for 2 minutes after which it exits
programming.
4. Press and hold down the PROG button of the TX1 remote
control until the motor starts to move in a direction
5. Release the PROG button: the motor will stop
UP
STOP
DOWN
PROG
6. Press the keys UP or DOWN depending on the way of motion
of the roll-up shutter before stopping:
- if the roll-up shutter was going up, press the key UP;
direction acquired: the key UP moves the roll-up shutter
UPWARDS, the key DOWN moves the roll-up shutter
DOWNWARDS.
- if the roll-up shutter was going down, press the key DOWN;
direction acquired: the key DOWN moves the roll-up shutter
DOWNWARDS, the key UP moves the roll-up shutter
UPWARDS.
7. To exit the programming mode, wait for the led to switch off
or press key 1 to exit immediately.
Try to operate the roll-up shutter and check that it works with the
logic above described. If the logic is reversed, it is necessary to
delete all the codes stored (See procedure "3. Deleting all
recorded transmitters") and start again the above procedure.
To add other remote controls, follow points 6, 7, and 8 of the
"QUICK transmitter recording"
Storing of the transmitters and selection of
the mode rolling shutter
To store the channel 1 of a transmitter TX1 in a blank control unit
1 controlling a roll-up shutter proceed as follows:
WARNING: the first transmitter stored fixes the direction of the
motion of the motor.
Repeat the procedure "1. Transmitter recording and sunshade
mode selection" by entering the code 12 11 12 in step 3.
Deletion of all the stored transmitters
To delete all the transmitters stored on the control unit it is
necessary using a remote control previously stored and proceed
as follows:
1. Supply power only to the motor to be programmed
2. Activate ADLER programming by holding down buttons 4 and
6 until the 6 LEDs turn on
3. Release the buttons and enter the code 12 11 13
The two highlighted digits indicate the remote control channel
recorded in the control unit; for channel 1 the digits are 11,
for channel 2 the digits are 12, for channel 3 the digits are 13,
etc up to channel 6. Once the codes have been entered, the
LED of the selected channel will blink for 2 minutes after
which it exits programming.
4. Hold down the PROG button until the motor starts to move
for about 1/2 second in both directions, indicating that the
deletion has been completed.
5. Release the PROG button
6. To exit the programming mode, wait for the led to switch off
or press key 1 to exit immediately.
To delete all the codes by means of a transmitter non-stored,
proceed as follows:
1. Switch off power supply of the system.
2. Activate ADLER programming by holding down buttons 4 and
6 until the 6 LEDs turn on
3. Release the buttons and enter the code 12 11 13
4. Press and keep pressed the button PROG
5. Power all control units where the deletion will be performed
6. Hold down the PROG button until the motor starts to move
for about 1/2 second in both directions, indicating that the
deletion has been completed.
7. Release the PROG button: the motor will stop
8. To exit the programming mode, wait for the led to switch off
or press key 1 to exit immediately.
15