cedamatic CP.GLISS.RI Manual De Instrucciones página 14

When operator assembly and wiring is completed, parameters and logic are programmed, self learning allows the operator to
learn the stroke and torque.
Enter menu Auto and press the button < PGM >, PUSH will be displayed.
Press again the button < PGM >: self-learning is beginning: PRG will be displayed, and the control panel completes some open-
ing/closing cycles.
When the procedure is completed OK will be displayed.
This procedure can be followed from any position of the gate/door leaf and can be stopped at any moment by pressing keys <+>
and <-> at the same time, or through the activation of STOP/PHO/PHA/DAS/PP/PED inputs.
If the procedure is not successful, the wording ERR appears. Check that no obstacles or frictions are present.
The programming of the various functions of the control unit is carried out using the LCD display on the control unit and setting the
desired values in the programming menus described below.
The parameters menu allows you to assign a numerical value to a function, in the same way as a regulating trimmer.
The logic menu allows you to activate or deactivate a function, in the same way as setting a dip-switch.
Other special functions follow the parameters and logic menus and may vary depending on the type of control unit or the software
release.
1 Press the button <PG>, the display goes to the first menu, Parameters "PAR".
2 With the <+> or <-> button, select the menu you want (PAR>>LOG>>RADIO>>NMAN>>RES)
3 Press the button <PG>, the display shows the first function available on the menu.
4 With the <+> or <-> button, select the function you want.
5 Press the button <PG>, the display shows the value currently set for the function selected.
6 With the <+> or <-> button, select the value you intend to assign to the function.
7 Press the button <PG>, the display shows the signal "PRG" which indicates that programming has been completed.
Simultaneously pressing <+> and <-> from inside a function menu allows you to return to the previous menu without making any
changes.
Simultaneously pressing <+> and <-> when the display is switched off shows the card software release.
Hold down the <+> key or the <-> key to accelerate the increase/decrease of the values.
After waiting 30s the control unit quits programming mode and switches off the display.
The tables below describe the individual functions available in the control unit.
MENU
Automatic closure time. It is activated only with "TCA"=ON logic.
TCA
At the end of the preset time, the control unit controls a closure operation.
Operating time. It is activated only with logics ENC : OFF.
TM
The operating time is adjusted during motor opening and closing phases.
The passage left open by the gate leaf during the partial opening (pedestrian) is
Tped
adjusted.
The area covered by the gate during the braking phase is adjusted.
TSM
0 = braking disabled.
PMo
The torque applied to the motor in the opening phase is adjusted.*
PMC
The torque applied to the motor in the closing phase is adjusted *.
PSo
The torque applied to the motor during braking in the closing phase is adjusted.*
PSC
The torque applied to the motor during braking in the opening phase is adjusted *
The trigger time of the anti-crash device (Encoder) is adjusted during the normal
SEAV
speed phase*.
99: maximum sensitivity – 0: Minimum sensitivity
The trigger time of the anti-crash device (Encoder) is adjusted during the braking
SEAR
phase*.
99: maximum sensitivity – 0: minimum sensitivity
Activated only with SERL:ON Logic. The activation time of the service light is ad-
TLS
justed.
14
RUN SELF-LEARNING AND ANTI-CRUSHING DEVICE SETTING
PROGRAMMING
To access programming:
PARAMETERS, LOGIC AND SPECIAL FUNCTIONS
PARAMETERS (PAR)
FUNCTION
Notes:
MEMO
MIN-MAX-(Default)
3-240-(40s)
1-250-(90s)
5-100-(15%)
0-100-(10%)
1-99-(40%)
1-99-(40%)
1-99-(50%)
1-99-(50%)
0-99-(1%)
0-99-(1%)
1-240-(60s)