Elko EP AirWS-100 Serie Manual Del Usuario página 3

ELKO EP, s.r.o.
Palackého 493
769 01 Holešov, Všetuly
Czech Republic
Tel.: +420 573 514 211
e-mail: elko@elkoep.com
www.elkoep.com
Made in Czech Republic
02-31/2018 Rev.: 0
Characteristics
• The sensor informs about the fi ll volume condition of the container, the waste
container, may trigger a requirement to empty it. It also informs you of the actual
temperature in the scanning area.
• It has a built-in sensor for opening the lid or for tipping over the waste container.
• With wireless technology and its compactness, the device can be used in a variety
of applications.
• Reliable measurement, regardless of material colour, transparency, gloss and in-
terference light.
• With the wireless solution and Sigfox / LoRa / NB-IoT communication, it can com-
municate instantly to your chosen location and be operated immediately.
• Data is sent to the server from which it can be subsequently displayed as a smart-
phone, application, or Cloud notifi cation.
• Battery status information is sent as a message to the server.
• Power: 2x Li-SOCL 3.6V (integrated) battery life up to 8 years according to fre-
2
quency of measurement and message transmission.
• The IP65 is suitable for installation in demanding environments.
Description
1
2
SET POWER-ON
3
1
3
1
Cloud app assignment
It is done in your Smartphone application. Enter the relevant information on the product
cover into the application.
1. Mounting hole Ø 5 mm
1
2. Magnetic contact
3. Ultrasonic sensor
2
4. Seal
3
1
4
1
AirWS-100
Ultrasonic fi ll-level sensor
General instrucions
Internet of Things (IoT)
• The IOT wireless communications category describes the Low Power Wide Area
(LPWA). This technology is designed to provide full-range coverage both inside and
outside buildings, energy-saving and low-cost operation of individual devices. Indi-
vidual networks - Sigfox, LoRa, NarrowBand - are available to use this standard.
Sigfox network information
• The network supports bidirectional communication but with a limited number of feed-
backs. It uses the free frequency band divided by Radio Frequency Zones (RCZ).
• RCZ1 (868 MHz) Europe, Oman, South Africa
• RCZ2 (902 MHz) North America
• RCZ3 (923 MHz) Japan
• RCZ4 (920 MHz) South America, Australia, New Zealand, Singapore, Taiwan
• Sigfox has more coverage across countries, so it is better suited for long distance moni-
toring.
• For more information on this technology, please visit www.sigfox.com.
LoRa network information
• The network is bidirectional and its communication uses free frequency band.
• 865 - 867 MHz
• 867 - 869 MHz
• 902 - 928 MHz
• The advantage of this network is the possibility of freely deploying individual stations
in local locations, thus strengthening their signal. It can therefore be used effi ciently in
company premises or, for example, in local parts of cities.
• For more information on this technology, please visit www.lora-alliance.org.
Information about the NarrowBand network
• The network provides two-way communication and the only one to use the licensed
LTE band. Our devices allow band 1 (2100MHz), Band 3 (1800MHz), Band 8 (900MHz),
Band 5 (850MHz), Band 20 (800MHz) and Band 28 (700MHz).
• It uses this SIM card technology for each device.
• The advantage of NarrowBand is the use of already built-up grids, which ensures suf-
fi cient reception outside and inside buildings.
• For more information on this technology, please visit www.vodafone.cz
Caution for proper operation:
• Products are installed according to the wiring diagram given for each product.
• For proper device functionality, it is necessary to have suffi cient coverage of the se-
lected network at the installation site.
• At the same time, the device must be registered in the network. Successful device reg-
istration on a given network requires a charge for traffi c.
• Each network off ers diff erent tariff options - it always depends on the number of mes-
sages you want to send from your device. Information on these tariff s can be found in
the current version of the ELKO EP pricelist.
Function
The sensor measures the temperature in the space every minute, simultaneously detects
the position of the sensor (e.g. opening the lid, tipping over the waste container, etc.). At
twelve hours *, ultrasonic sensors scan the distance between the sensor and the surface
being scanned.
Data reports measured values sent in twelve-hour period*. In the case of detecting
changes in position of the sensor (opening of the lid, etc.) in 5 minutes*. In the event of a
sharp rise in temperature it is reported immediately.
Settings: by using supplied magnet (included in the supply).
* Intervals can be set by message from the server.
1 / 2
India
Europe
North America, Japan, Korea
EN