Eaton All-Pro WP1050LPC Manual De Instrucciones

WP1050LPC
WP1850LPC
WP1050L
WP1850L
ENGLISH
ITEMS REQUIRED
(Purchase separately)
• Phillips screwdriver
• Outdoor weatherproof silicone caulking
IMPORTANT SAFETY INSTRUCTIONS
When using product, basic precautions should always be followed, including the following:
• Heed all warnings, including below warnings AND those included on product.
• Save these instructions and warnings.
• cULus LISTED for outdoor, wet location use not to exceed 40˚C ambient.
• Disassembling your fixture will void the warranty.
• Your fixture is prewired and preassembled for easy installation.
WARNING
• Read and follow these instructions.
• Risk of fire/electric shock. If not qualified, consult an electrician.
• Disconnect power at fuse or circuit breaker before installing or servicing.
CAUTION
• Connect fixture to a 120 volt, 60 Hz power source. Any other connection voids
the warranty.
• Fixture should be installed by persons with experience in household wiring or by a
qualified electrician. The electrical system, and the method of electrically connecting
the fixture to it, must be in accordance with the National Electrical Code and local
building codes.
• Fixture designed for wall mount to a recessed junction box only. Mount fixture to a
grounded standard junction box marked for use in wet locations.
• Suitable for mounting within 4 feet of the ground.
• Fixture is suitable for ground mounting only when used with optional trunnion mount
accessory kit, catalog number WPFLD-TRN (sold separately).
• This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause
undesired operation.
WARNING: FCC Regulations state that any unauthorized changes or
modifications to this equipment not expressly approved by the manufacturer
could void the user's authorization to operate this equipment.
Questions?/Des questions?/ ¿Preguntas? 1-800-334-6871 ConsumerProducts@eaton.com
PACKAGING CONTENTS/ CONTENU DE L'EMBALLAGE/CONTENIDO DEL PAQUETE
A. Housing B. Back cover (Preinstalled to housing)
Boîtier
Alojamiento
Instruction Manual/Manuel d'instructions/ Instrucciones
Couvercle arrière (préinstallé sur le boîtier)
Cubierta trasera (preinstalada en el alojamiento)
SAVE THESE INSTRUCTIONS.
FOR BEST RESULTS
• Do not mount fixture close to reflective surfaces
such as windows, white walls, white surfaces
and water.
• When mounting to a wall, make sure the fixture
is 7 in. on center away from eave and 13 inches
on center away from inside corner of the
exterior wall (Fig. 1).
MOUNTING AND WIRING YOUR FIXTURE
WARNING: Risk of electric shock. Disconnect
power at fuse or circuit breaker before installing
or servicing.
NOTE: Back cover mounts to the following types of
recessed junction boxes: 4 in. square, 4 in. round, 4 in.
octagonal, 3-1/2 in. square / octagonal, masonry, 2-3/4
in. hole pattern boxes, and single gang outlet.
1. Unscrew housing from back cover. Confirm junction
box mounting screw pattern and ONLY remove the
gasket material from the back cover required for
installation.
2. Mount the back cover to the junction box using the
#8 screws provided. See (Fig. 2) for proper back
cover orientation based on desired lighting direction.
3. Caulk around back cover where it contacts the
mounting surface to provide a watertight seal.
4. For downlight applications, temporarily secure the
housing to the back cover using the hanging tab
provided on the back cover (Fig. 3a). For uplight
applications, temporarily secure the housing to the
back cover using the tabs provided on the back
cover (Fig. 3b).
1
C. (2) #8-32 x 3/4 in. junction box screws
(2) vis nº 8 de 32 x 3/4 po pouboîtier de jonction
(2) tornillos #8-32 x 3/4 pulg. para montaje de la caja de
conexiónes
1
7in
13in
2
Housing Screw Tab
Downlight
3a
Downlight
3b Uplight
13in
C
Uplight