Slcbl Connection / Termination Kits; Slcbl, Slmcbl, Slhcbl Connection / Termination Kits - BriskHeat SLCBL Serie Manual De Instrucciones De Instalación Y Mantenimiento

SLCBL Connection / Termination Kits

For use in ordinary locations with SLCBL cable only (UL approved).
For use in roof & gutter snow melting & de-icing applications with SLCBL cable only (UL approved).
Approvals valid only when used with appropriate heating cable and installation accessories,
and installed in accordance with all applicable instructions, codes, and regulations.
SLCBLUC: SLCBL Power Connection Kit
Kit Contents:
2 Heat-trace warning labels
2 De-icing snow melt caution labels
1 Standoff pipe mounting bracket
1 Lock nut
1 1/2"NPT Seal fitting with strain relief and grommet
Enough to complete:
One input power connection and one end seal termination.
NOTE: Junction box and pipe strap sold seperately. Requires UL Listed junction box suitable for the location with a clearance hole for 1/2" conduit or
1/2" NPT thread hub. For heating cable with no outer-jacket (Type -B only), a metallic junction box must be used to ensure proper grounding.
SLCBLUC-GF: Ground Fault Power Connection Kit
Kit Contents:
2 Heat-trace warning labels
2 De-icing snow melt caution labels
1 Cloth tape
2 Mastic strips
2 Clamp ties
2 Crimp-on insulated terminals
1 Crimp-on non-insulated barrel
Enough to complete:
One ground-fault protection power input power connection.
SLCBLKC: SLCBL End Seal Kit
Kit Contents:
2 Heat-shrink caps
2 Heat-shrink tubes 3/4" x 5" (19mm x 13cm)
Enough to complete:
Two end seal terminations.
SLCBLSK: SLCBL Splice and Tee Kit
Kit Contents:
1 Clamp tie 1 Black heat-shrink tube 1" x 8" (25mm x 20cm)
3 Cable ties 3 Black heat-shrink tubes 1/2" x 1" (13mm x 25mm)
1 Cloth tape 6 Black heat-shrink tubes 1/8" x 1" (3mm x 25mm)
5 Matic strips 2 Crimp-on insulated terminals
Enough to complete:
One splice connection and one end seal termination or one tee connection and one end seal termination.
NOTE: This kit does not complete an input power connection
®
© BriskHeat
Self Regulating Heating Cable
3 Wire nuts
1 Black heat-shrink tube 1/2" x 1" (13mm x 25mm)
1 Green/Yellow heat-shrink tube 1/4" x 6" (6mm x 15cm)
2 Black heat-shrink tubes 1/8" x 5-1/2" (3mm x 14cm)
1 Sealing gasket
1 End seal
1 Heat-shrink tube 3/4" x 8" (19mm x 20cm)
1 Heat-shrink tube 3/4" x 5" (19mm x 13cm)
2 Heat-shrink tubes 1/8" x 1" (3mm x 25mm)
1 Heat-shrink tube 1/2" x 1" (13mm x 25mm)
1 Heat-shrink tube 5/16" x 1-1/2" (8mm x 38mm)
1 Ground fault device with 120V 3-Prong NEMA 5-15 plug
2 Woven braid sleeves 1/2" x 4" (13mm x 10cm)
2 Heat-shrink caps
1 Heat-shrink tube
1 Crimp-on non-insulated barrel
1 End seal
Corporation. All rights reserved.
13

SLCBL, SLMCBL, SLHCBL Connection / Termination Kits

For use in Hazardous Area Locations with SLCBL (BP, BF) cable only (CSA approved).
For use in non-hazardous area locations with SLCBL, SLMCBL, SLHCBL cable (non-CSA approved).
Approvals valid only when used with appropriate heating cable and installation
accessories, and installed in accordance with all applicable instructions, codes, and
regulations.
Hazardous (Classified) Locations
Class I, Division 2, Groups A, B, C, D
Class II, Division 2, Groups E, F, G
Class III
PTBO-GET: SLCBL, SLMCBL, SLHCBL Power Connection Kit With Octagon Enclosure
Kit Contents:
1 Octagon junction box with terminal power connections
1 Pipe standoff mounting bracket
2 Pipe Straps
1 Lock nut
1 Sealing gasket
Enough to complete:
One input power connection.
JHE-GET: SLCBL, SLMCBL, SLHCBL Low-Profile End Seal Kit
Kit Contents:
1 End seal housing
1 Watertight sealing grommet
3 Pressure seal end with screws
Enough to complete:
One low-profile end seal termination.
JHS-GET: SLCBL, SLMCBL, SLHCBL Low-Profile Splice Connection Kit
Kit Contents:
1 In-line splice housing
2 Watertight sealing gaskets
2 Housing covers with screws
2 Watertight sealing grommets
2 Pressure seal ends with screws
Enough to complete:
One low-profile splice termination.
JHT-GET: SLCBL, SLMCBL, SLHCBL Low-Profile Tee Connection Kit
Kit Contents:
1 Tee splice housing
2 Watertight sealing gaskets
2 Housing covers with screws
3 Watertight sealing grommets
3 Pressure seal ends with screws
Enough to complete:
One low-profile tee connection.
NOTE: This kit does not complete an input power connection.
®
© BriskHeat
Self Regulating Heating Cable
1 M25x1.5 IP68 Seal fitting
2 Watertight sealing grommets
1 Watertight sealing plug
2 Green/Yellow heat-shrink tube 1/4" x 6" (6mm x 15cm)
2 Black heat-shrink tube 1/8" x 5-1/2" (3mm x 14cm)
Corporation. All rights reserved.
14