Thetford Sanicon turbo 400S Manual Del Propietario Y Instrucciones De Instalación página 8

Operation, cont'd.
EMPTY GRAY WATER TANK(S)
Refer to Fig. 1 and Fig. 5.
1. ENSURE universal nozzle (
dump station! Refer to "Attach to Dump Station" procedure.
TIP For Cleaner Storage: Emptying black water tank fi rst,
NOTICE
allows gray water to cleanse the system.
2. Open gray water tank gate valve (
3. Use ( ) to turn pump on.
K3
4. Do not leave unit unattended.
5. Use ( ) to turn pump off.
K3
TIP: The hose expands as fl uid moves to dump station
NOTICE
and contracts when tank is empty.
6. Close gray water tank gate valve
7. Repeat Steps 2-6 for secondary gray tanks.
Gray water bypass is possible if the discharge
NOTICE
plumbing does not fl ow upward.
PREPARE HOSE FOR STORAGE
Refer to Fig. 1 and Fig. 5.
1. Ensure pump is off.
2. Drain hose ( K2 ) by holding at a sloped angle to direct excess
water into the dump station.
TIP For Faster Draining: Leave gray gate valve
NOTICE
open allowing hose to vent and expediting the process.
3. Disconnect nozzle ( K2.2
4. Install cap(s) ( K2.3, K2.4
5. Return hose to coach hose compartment (
connected to coach.
Helpful Hints
■ Additional hoses can be purchased from Thetford and used
to extend the length of the evacuation hose. Connect the
hoses using 1.5" (3.8 cm) barbed coupling with clamp.
■ If you wish to extend the evacuation hose, connect a .75"
(1.9 cm) inner diameter garden hose to the end of the
nozzle.
A longer evacuation hose reduces fl ow rate.
NOTICE
■ Before storing the hose, make sure that all liquid has drained from
the hose.
Gray water bypass is possible if the discharge plumbing
NOTICE
does not fl ow upward.
®
SANICON Turbo Model 400S - Permanent Bayonet Mount
K2.2 ) is securely attached to
).
5B
(5B) .
(5B)
) from dump station.
).
5C ); leave hose
Obstruction Removal
Refer to Fig.1 and Fig. 5.
Be sure to have container available for captur-
NOTICE
ing system fl uid!
1. Ensure all contents have been drained from system.
Turn off power and remove pump fuse. Once the obstruc-
AVISO AVIS
! ! ! ! NOTICE ATTENTION ATENCIÓN CAUTION DANGER
tion is removed, there is potential injury to hands or
ATTENTION ATTENTION ATTENTION
fi ngers in the path of the impeller if the power is on!
2. Disconnect the power by removing the pump fuse or discon-
necting the battery.
3. Verify all gate valves ( 5B
4. Locate pipe hanger (K6)
Plumbing from the discharge port (
NOTICE
be disconnected.
5. Remove the pump from the RV outlet (
Do NOT remove pump housing. Obstruction MUST be
AVISO
! ! ! ! NOTICE ATTENTION ATENCIÓN CAUTION DANGER AVIS
removed through inlet.
ATTENTION ATTENTION ATTENTION
6. Remove the obstruction.
7. Attach the pump inlet to the RV outlet (
and pipe hanger.
8. Reconnect the power.
9. Operate system using gray water; check for leaks.
Winterizing
Refer to Fig. 1 and Fig. 5.
1. Ensure all tanks are empty.
2. Pour RV antifreeze into the empty black water tank.
Be sure to have container available for capturing system
NOTICE
fl uid!
3. Turn on pump.
4. Run pump until the antifreeze begins to discharge from
universal nozzle (
K2.2
5. Turn pump switch to the Off position.
6. Drain hose ( ) by holding at a sloped angle to remove
K2
excess water; return hose to storage position.
8
) are closed.
and loosen clamp bolt.
) may need to
K1.1
).
5E
) and tighten hose
5E
).
97652 Rev. C (04.05.18)