Safety Instructions; Intended Use Of The Product; Product Description; Particular Advantages - Hedson IRT QuickSpot 3 Manual De Instrucciones

1.

Safety instructions

The dryer must not be exposed to paint fog, sanding
dust or solvents, due to fire risk. Furthermore, this will
reduce the lifetime of the dryer. Allow for sufficient cool-
ing time of the dryer. The distance to the object to be
dried must be sufficient. Otherwise there is risk for fire
or explosion! Keep all flammable materials in a sufficient
distance from the hot surfaces of the dryer.
1.1 Hazards
Fire and explosion
Do not store, prepare or use solvent-containing materials
within a 5 m/16 feet radius of the mobile dryer. Flam-
mable materials should not be placed close to a drying
device in use.
Never direct the cassette towards highly combustible
materials.
Electrical equipment
The dryer is operated with high electrical voltage, which
can be highly dangerous.
Before accessing live parts, remove the main
connector from the wall socket. Only professional electri-
cians may have direct access to the electrical compo-
nents.
If the supply cord is damaged, it must be replaced by
the manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
WARNING !
Intensive heat radiation. Hands, face and
other parts of the body should be exposed
as little as possible to the heat radiation.
2.

Intended use of the product

This product serves exclusively to accelerate the drying/
curing of putty, filler, base and clear coats. This applies
to both water-borne and solvent-based products. It´s site
of use is the preparation area and finishing area. Within
the automotive industry and vehicle repair sectors, it is
used to cure small areas before polishing. The product
must not be used for other purposes than the described
drying processes. The maximum ambient temperature
during operation should not exceed 40°C. The IRT
QuickSpot dryers must not be used in spray booths or
within a distance of 5 m from spraying activities in order
to avoid explosion risk.
195996 rev 2
3.

Product description

The dryer is an essential aid for paint repair on small
sized areas.
The easily manoeuvrable IRT QuickSpot is equipped with
one cassette. The cassette is equipped with three infra-
red (IR) lamps with gold plated freeform reflectors and a
ventilator. The design, combined with the distance rods,
makes positioning of the cassette simple. The IR lamps
are easily exchangeable and the reflectors are protected
against mechanical damage by a mesh. The dryer has a
selection of sophisticated programs.
3.1

Particular advantages

3.1.1 Higher quality
Using the dryer when you cure putty also improves the
quality of the top coat.
The shortwave IR curing enables the coating to be cured
from the inside outwards. This prevents solvents to be
trapped inside the coating and ensures a fast and high
quality curing.
3.1.2 Short drying times
Preset drying programs
PROGRAM TIME (S) POWER LEVEL
P1 18
20
P2 24
14
P3 22
16
P4 20
18
P5 31
7
P6 29
9
P7
20
18
P8 20
18
P9 26
12
3.1.3 High tech shape of reflectors with short wave IR
By using short- and medium-wave technology and
gold-coated reflectors with a high tech shape important
advantages are achieved. Firstly, by radiating only the
needed areas and not heating any air, a lower energy
consumption is achieved. Secondly, a more uniform
surface temperature is obtained by distributing the en-
ergy evenly. Thirdly, a larger drying surface is achieved.
Fourthly, less radiation outside the curing area.
EN
TYPE
6 Flash Off
1 Full Bake
4 Flash Off
1 Full Bake
4 Flash Off
1 Full Bake
5 Flash Off
1 Full Bake
4 Flash Off
1 Full Bake
4 Flash Off
1 Full Bake
3 Flash Off
1 Full Bake
2 Flash Off
1 Full Bake
2 Flash Off
1 Full Bake
3