Disposal Information; Online Support - Dyson v7 Instrucciones De Seguridad

Ocultar thumbs Ver también para v7:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Emptying the clear bin
• Empty as soon as the dirt reaches the level of the MAX mark – do not overfill.
• Ensure the machine is disconnected from the charger before emptying the clear bin.
Be careful not to pull the "ON" trigger.
• To make emptying the clear bin easier, it is advisable to remove the floor tool.
• To minimize dust/allergen contact when emptying, encase the clear bin tightly in a
plastic bag and empty.
• To release the dirt, hold the machine by the handle, pull the red lever back and lift
upwards to release the cyclone. Continue until the bin base automatically opens and
releases the dirt.
• Remove the clear bin carefully from the bag.
• Seal the bag tightly, dispose as normal.
• To close, push the cyclone downwards until it is in the normal position and manually
close the base of the bin – the base will click when it is securely in place.
Cleaning the clear bin
• Ensure the machine is disconnected from the charger before removing the clear bin.
Be careful not to pull the "ON" trigger.
• Remove the floor tool.
• To remove the cyclone, hold the machine by the handle, pull the red lever towards
you and lift upwards until the bin opens, then push in the red button located behind
the cyclone and lift the cyclone out.
• To detach the clear bin from the machine, pull back on the red catch located at the
base, slide the clear bin down and carefully remove forwards from the main body.
• Clean the clear bin with a damp cloth only.
• Do not use detergents, polishes or air fresheners to clean the clear bin.
• Do not put the clear bin in a dishwasher.
• Ensure the clear bin is completely dry before replacing.
• To replace the clear bin, align the tabs on the clear bin with the grooves on the main
body and slide upwards into place until the catch clicks.
• Slide the cyclone into the grooves of the main body and push downwards until it is in
its normal position and manually close the base of the bin – the base will click when
it is securely in place.
Washing your filter
• Ensure the machine is disconnected from the charger before removing the filter. Be
careful not to pull the "ON" trigger.
• Your machine has one washable filter, located as shown.
• To remove the filter, lift it out of the top of the machine.
• Check and wash the filter regularly according to instructions to
maintain performance.
• The filter may require more frequent washing if vacuuming fine dust or if used
mainly in "POWERFUL SUCTION" mode.
• Wash the filter with cold water only.
• Run water over the outside of the filter until the water runs clear.
• Squeeze and twist with both hands to make sure the excess water is removed.
• Lay the filter on its side to dry. Leave to dry completely for a minimum of 24 hours.
• Do not put the filter in a dishwasher, washing machine, tumble dryer, oven,
microwave or near an open flame.
• To refit, place the dry filter back into the top of the machine. Make sure it is seated
properly.
Looking for blockages
The motor will pulse when there is a blockage. Please follow the instructions below
to locate the blockage:
• Ensure the machine is disconnected from the charger before looking for blockages.
Be careful not to pull the "ON" trigger.
• Do not operate while checking for blockages as doing so could result in
personal injury.
• Beware of sharp objects when checking for blockages.
• To check for blockages in the main body of the machine, remove the clear bin and
cyclone as per the instructions in the cleaning the clear bin section and remove the
blockage. Please consult the 'Stubborn blockages' section of the illustrations for
further guidance.
• If you cannot clear an obstruction you may need to remove the brush bar. Use a
coin to unlock the fastener marked with a padlock. Remove the obstruction. Replace
the brush bar and secure it by tightening the fastener. Ensure it is fixed firmly before
operating the machine.
• This machine has carbon fiber brushes. Take care if coming into contact with
them, as they may cause minor skin irritation. Wash your hands after handling
the brushes.
• Refit all parts securely before using.
• Clearing blockages is not covered by your warranty.
Blockages – automatic cut-out
• This machine is fitted with an automatic cut-out.
• If any part becomes blocked the machine may automatically cut out.
• This will happen after the motor pulses a number of times (i.e switches on and off in
quick succession).
• Leave to cool down before looking for blockages.
• Ensure the machine is disconnected from the charger before looking for blockages.
Failure to do so could result in personal injury.
• Clear any blockage before restarting.
• Refit all parts securely before using.
• Clearing blockages is not covered by your warranty.
Charging and storage
• This machine will switch "OFF" if the battery temperature is below 37.4°F (3°C).
This is designed to protect the motor and battery. Do not charge the machine and
then move it to an area with a temperature below 37.4°F (3°C) for storage purposes.
• To help prolong battery life, avoid recharging immediately after a full discharge.
Allow to cool for a few minutes.
• Avoid using the machine with the battery flush to a surface. This will help it run
cooler and prolong battery run time and life.
10
10
10.04.2017 11:57 - C88015_HH11_OPMAN_US_X285A-NON-HEPA-OPMAN-88015.indd_15_4c0s
Diagnostics – battery
When in use, trigger pressed:
Solid blue: 'ON'.
Flashing blue: No power, charge battery.
Flashing amber: No power, temporary fault
(e.g. too hot/cold).
Solid amber: Fault (contact Dyson Helpline).
Flashing red: Fault (contact Dyson Helpline).
When charging battery:
Solid blue: Charging.
Flashing blue: Not charging – Re-fit charger or try another
socket. If warning light persists, contact Dyson Helpline.
Lights off: Charging complete.
Solid amber: Not charging, temporary fault (e.g. too hot/cold).
Flashing red: Fault (contact Dyson Helpline).
Battery Safety Instructions
• If the battery needs replacing please contact the Dyson Helpline.
• Use only Dyson chargers for charging this Dyson machine.
• The battery is a sealed unit and under normal circumstances poses no safety
concerns. In the unlikely event that liquid leaks from the battery do not touch the
liquid and observe the following precautions:
– Skin contact – can cause irritation. Wash with soap and water.
– Inhalation – can cause respiratory irritation. Expose to fresh air and seek medical
advice.
– Eye contact – can cause irritation. Immediately flush eyes thoroughly with water
for at least 15 minutes. Seek medical attention.
– Disposal – wear gloves to handle the battery and dispose of immediately, follow-
ing local ordinances or regulations.
Caution
The battery used in this device may present a risk of fire or chemical burn if
mistreated. Do not disassemble, short contacts, heat above 140°F (60°C), or
incinerate. Keep away from children. Do not disassemble and do not dispose of
in fire.

Disposal information

• Dyson products are made from high grade recyclable materials. Recycle
where possible.
• Dispose of or recycle the battery in accordance with local ordinances or regulations.
• The battery should be removed from the product before disposal.

Online support

• For online help, general tips, videos and useful information about Dyson.
www.dyson.com/support

Publicidad

Tabla de contenido
loading

Tabla de contenido