Intended Use - SIOUX A Serie Manual De Instrucciones Y Lista De Piezas

Ocultar thumbs Ver también para A Serie:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 7
The use of any accessory with this tool not provided or specified by Sioux Tools can perform unpredictably.
Use only accessories provided or specified by Sioux Tools.
Tools that perform unpredictably can cause injury.
When disposing of a tool, do it in a way that does not harm personnel or the environment.

INTENDED USE

This tool is intended for use with small mounted abrasive wheel for precision material removal.
AIR SUPPLY
The efficiency and life of this tool depend on the proper supply of clean, dry air at a maximum of 90 PSI. The use of an air line filter,
pressure regulator, and lubricator is recommended.
Before connecting to tools, blow out the air line to remove water and dirt that may have accumulated.
HOSE AND HOSE CONNECTIONS
The air supply hose recommended is 3/8" (10mm) I.D. If an extension hose is necessary, use 1/2" (13mm) ID hose with couplings not
less than 3/8" (10mm) I.D.
LUBRICATION
All models may operate without airline lubrication. However, operating the tool without airline lubrication may reduce tool performance
and vane life.
If an airline lubrication is not used, it is recommended that the tool be oiled daily before use to improve performance. Add 2-4 drops of air
motor oil and run the tool for 10-20 seconds to distribute oil through the tool.
For maximum performance and tool life, an air line lubricator, set to deliver 2 drops per minute, is recommended. SIOUX No. 288 Air
Motor Oil is recommended.
MAINTENANCE
Water, dust and other airline contaminants can cause rust and vane sticking. For long periods between tool use, flush the tool with a few
drops of oil and run for 10 seconds. This will help remove contaminants and reduce the formation of rust.
OPERATION
Always remove the tool from the air supply be for installing or changing sanding discs!
To install a sanding disc:
1. Install the 4 1/2 (114.3 mm) backing pad on the spindle. The 3" (76.2 mm) backing pad can be installed behind the 4 1/2 (114.3 mm)
for additional rigidity. DO NOT USE THE 3" (76.2 mm) BACKING PAD WITHOUT THE 4 1/2 (114.3 mm) BACKING PAD!
2. Install the sanding disc.
3. Install the retaining nut.
4. Insert the lever into the hub.
5. Turn the sanding disc by hand to tighten.
Start the tool by depressing the trigger.
Maintain a slight angle between the sanding disc and the work.
Do not use excessive pressure. Excessive pressure will cause the tool to slow down. Sanders work best at higher speeds.
We, Sioux Tools Inc., 250 Snap-on Drive, P.O. Box 1596, Murphy, NC, 28906, USA, declare under our sole responsibility that the products
to which this declaration relates are in conformity with the following standard or standards or other normative document or documents:
August 1, 2007
Murphy, North Carolina, USA
Date and place of issues
WARNING
SOUND AND VIBRATION READINGS
*Sound Pressure
Catalog No.
dBA
SPS10P18
80.0
*per PN8NTC1
DECLARATION OF CONFORMITY
EN 792, EN 292 Parts 1&2, ISO 8662, Pneurop PN8NTC1
following the provisions of
89/392/EEC as amended by 91/368/EEC & 93/44/EC Directives.
Mark S. Pezzoni
President
Power and Specialty Tools
Name and position of issuer
*Sound Power
dBA
91.6
Less than 2.5
*per PN8NTC1
*per ISO 8662
SPS10P18
3
*Vibration
m/s
2
Signature of issuer

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Sps10p18

Tabla de contenido