120V Small Led Board Replacement; 120V Small Light Driver (Pcb) Replacement; Large Light Driver (Pcb) Replacement (120V And 12V); Reassemble The Fixture - Jandy Pro Serie Manual De Instalación Y Funcionamiento

Jandy
POOL LIGHT
ASSEMBLY
Power
Niche
Cord
Bonding
cable
Figure 6. Removing the Jandy Pro Series
WaterColors RGBW LED Light Assembly
for Light Driver Replacement
7. Place a washer on the other stud and place the
green ground wire terminal on the washer and
secure both with the nut. Torque to 12 in-lbs.
8. Plug in the quick disconnect wire (white) onto the
terminal ACL (TP-1) of the light engine.
9. Plug in the quick disconnect wire (black) onto
terminal ACN (TP-2) of the light engine.
7.3

120V Small LED Board Replacement

1. Disconnect power and wait 5 minutes.
2. Remove two (2) screws and six (6) washers.
3. Unplug the board connector from the light engine.
4. Remove the LED board from the heat sink. If
you are also replacing the driver board, you can
proceed now to step 7.4
5. Apply thermal grease to the back of the new LED
board.
6. Place new LED board into the heat sink with the
orientation shown in Figure 7.
7. Secure the LED board with two (2) screws and
two (2) washers.
8. Plug in the board connector.
7.4 120V Small Light Driver (PCB)
Replacement
1. Disconnect power and wait 5 minutes.
2. Remove LED board as instructed in step 7.3
3. Remove 2 screws from the heat sink and remove
the heat sink.
4. Remove both quick disconnect wires from the
PCB. Note that the black wire is connected to
ACN and the White wire is connected to ACL.
5. Remove 2 metal posts from the driver board
Pro Series, WaterColors RGBW LED Lights
®
POOL WALL
Unscrew pilot screw
and pull top of light
1
assembly away from
pool wall
PILOT SCREW
2 Push up on
bottom of
light assembly
|
Installation Manual
6. Remove driver board and place new light driver
board into the fixture with the orientation shown
SPA LIGHT
in Figure 7.
ASSEMBLY
7. Insert metal posts back on to the screw studs.
Power
Niche
Cord
8. Plug in both quick disconnect wires, white onto
the terminal ACL of the light driver and black
Bonding
cable
onto the ACN.
9. Align heat sink to the metal posts
10. Secure the heat sink with 2 screws
11. Apply thermal grease to the back of the new LED
board.
12. Place new LED board into the heat sink with the
orientation shown in Figure 7.
13. Secure the LED board with two (2) screws and
six (6) washers.
14. Plug in the board connector.
7.5 Large Light Driver (PCB) Replacement
(120V and 12V)
1. Disconnect power and wait 5 minutes.
2. Unplug the quick disconnect terminals and the
grounding wire (green) from the light driver.
3. Remove three (3) nuts and washers.
4. Remove the LED board, light driver board and
board connector from the light fixture.
5. Apply thermal grease to the back of the new LED
board.
6. Place new LED board and light driver board into
the fixture with the orientation shown in Figure 8.
7. Secure the new boards with 3 washers, spilt
washers and nuts. Torque to 12 in-lbs.
8. Plug in the white quick disconnect wire onto the
terminal AC1 (TP-L) of the light driver board.
9. Plug in black quick disconnect wire onto terminal
AC2 (TP-N) of the light driver. Ensure board
connectors are connected to both boards.
10. To secure the ground wire, place the flat washer,
followed by the ground wire, followed by the split
washer, securing in place with the nut. Torque to
12 in-lbs.
7.6

Reassemble the Fixture.

1. If not already done, remove the gasket from the
glass lens and install a new gasket on the lens. On
the small light, remove the diverger from the lens.
NOTE
A new lens gasket must be used each time the light is
reassembled.
Page 11
ENGLISH
SPA WALL
Unscrew pilot screw
1
and pull top of light
assembly away from
spa wall
PILOT SCREW
2
Push up on
bottom of
light assembly