Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
10
9)
Install remaining components.
Table
Maximum Capacity of Metallic Pipe in Cubic Feet of Gas per Hour for Gas Pressures of 2 psi or Less and
6.2(a)
Nominal
Actual
Iron Pipe
ID:
Size
(Inches)
10
(Inches)
1/4
.364
32
3/8
.493
72
1/2
.622
132
3/4
.824
278
1
1.049
520
1 1/4
1.380
1050
1/12
1.160
1600
2
2.067
3050
2 1/2
2.469
4800
3
3.068
8500
4
4.026
17500
© 2009 National Fire Protection Association, Inc. and International Approval Services - U.S., Inc. All Rights Reserved.
INSTALLATION/GAS INSTRUCTIONS
a Pressure Drop of 0.3 Inch Water Column. (Based on a 0.60 Specific Gravity Gas)
20
30
40
50
22
18
15
14
49
40
34
30
92
73
63
56
190
152
130
115
350
285
245
215
730
590
500
440
1100
890
760
670
2100
1650
1450
1270
3300
2700
2300
2000
5900
4700
4100
3600
12000
9700
8300
7400
TYPICAL NATURAL GAS SUPPLY INSTALLATION
We recommend that this installation be done by a LICENSED professional.
GENERAL SPECIFICATIONS FOR PIPING
Note - Contact your local municipality for building codes regulating outdoor
gas grill installations. In absence of Local Codes, you must conform to the latest
edition of National Fuel Gas Code ANSI Z223.1/NFPA54.
•
This grill is designed to operate at 4.5 inches of water column pressure.
•
A manual shut-off valve must be installed outdoors, and be accessible, not in the
"built-in" structure. An additional manual shut-off valve indoors should be installed
in the branch fuel line in an accessible location near the supply line.
CAUTION: If young children are in the area, a locking valve
should be considered.
•
Pipe compound should be used which is resistant to the action of liquid propane
gas when gas connections are made.
•
The gas connections must be firmly attached to a rigid, permanent construction.
Note: The information provided in this manual is general for typical installations.
We cannot cover all possible installation ideas. We recommend, prior to
installation, that you contact your municipality for local building codes and your
local fire department for installation verification.
If you have any questions, contact the Customer Service Representative in your
area using the contact information on our web site. Log onto www.weber.com
GAS LINE PIPING
•
Refer to piping chart.
•
The corrugated gas line from the manifold is 58 inches (1,473.2 mm) long. Do not
extend the gas line.
•
We have provided the means to make an SAE 45° flare connection. Do not use
pipe sealant on this connection.
•
If the length of line required does not exceed 50 feet, use a 5/8" O.D. tube. One
size larger should be used for lengths greater than 50 feet. Refer to piping chart.
•
Gas piping may be copper tubing, type K or L; polyethylene plastic tube, with a
minimum wall thickness of .062 inch (1.57 mm); or standard weight (schedule 40)
steel or wrought iron pipe.
•
Copper tubing must be tin-lined if the gas contains more than 0.3 grams of
hydrogen sulfide per 100 cubic feet of gas.
•
Plastic tubing is suitable only for outdoor, underground use.
•
Gas piping in contact with earth, or any other material which may corrode the
piping, must be protected against corrosion in an approved manner.
•
Underground piping must have a minimum of 18" cover.
Length of Pipe (Feet)
60
70
80
90
12
11
11
10
27
25
23
22
50
46
43
40
105
96
90
84
195
180
170
160
400
370
350
320
610
560
530
490
1150
1050
990
930
1850
1700
1600
1500
3250
3000
2800
2600
6800
6200
5800
5400
100
125
150
175
9
8
8
7
21
18
17
15
38
34
31
28
79
72
64
59
150
130
120
110
305
275
250
225
460
410
380
350
870
780
710
650
1400
1250
1130
1050
2500
2200
2000
1850
5100
4500
4100
3800
WWW.WEBER.COM
®
.
200
6
14
26
55
100
210
320
610
980
1700
3500
®
Publicidad
Tabla de contenido
