Metra 95-7326 Instrucciones De Instalación

Hyundai elantra 2007-2010

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Hyundai Elantra 2007-2010
(US Model Only) (Non Radio Delete) (Non Touring Model)
KIT FEATURES
• ISO DDIN radio provision
KIT COMPONENTS
• A) ISO DDIN trim plate • B) ISO DDIN brackets
A
B
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: • 70-1004 • 70-7303
Antenna Adapter: • Not required
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver • Cutting tool
METRA. The World's best kits.
Installation instructions for part 95-7326
95-7326
metraonline.com
Table of Contents
Dash Disassembly ................................................. 2
Kit Assembly
– ISO DDIN radio provision ...................................... 3
CAUTION!
Metra recommends disconnecting the negative bat -
tery terminal before beginning any installation, unless the vehicle
manufacturer recommends against so. Please check with your local
Dealership for more information. All accessories, switches, climate
controls panels, and especially air bag indicator lights must be con -
nected before reconnecting the battery or cycling the ignition. Also,
do not remove the factory radio with the key in the on position, or the
vehicle running. It would be best to remove the key from the ignition
and then wait a few seconds before removing the factory radio.
© COPYRIGHT 2004-2015 METRA ELECTRONICS CORPORATION

Publicidad

Tabla de contenido
loading

Resumen de contenidos para Metra 95-7326

  • Página 1 KIT COMPONENTS • A) ISO DDIN trim plate • B) ISO DDIN brackets CAUTION! Metra recommends disconnecting the negative bat - tery terminal before beginning any installation, unless the vehicle manufacturer recommends against so. Please check with your local WIRING & ANTENNA CONNECTIONS (sold separately) Dealership for more information.
  • Página 2: Dash Disassembly

    95-7326 Dash Disassembly 1. Unclip and remove the panel surrounding the radio, including the a/c vents and hazard button. (Figure A) 2. Remove (4) Phillips screws to remove radio. (Figure B) Continue to kit assembly (Figure B) (Figure A)
  • Página 3: Kit Assembly

    (Figure A) Note: The smoother the cut, the CUT OUT BAR better the 95-7326 will look in the dash panel. CUT HERE 2. Snap the ISO DDIN brackets into the inside edge of the ISO DDIN trim plate.
  • Página 4: Important

    Installation instructions for part 95-7326 IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated.
  • Página 5: Características Del Kit

    Instrucciones de instalación para la pieza 95-7326 Indice Hyundai Elantra 2007-2010 Desmontaje tablero ..........2 (US sólo modelo) (No radio eliminar) (Modelo para no Touring) 95-7326 Ensamble del kit – Provisión de radio ISO DDIN ......... 3 CARACTERÍSTICAS DEL KIT •...
  • Página 6: Desmontaje Tablero

    95-7326 Desmontaje tablero 1. Suelte y retire el panel que rodea la radio, incluyendo las rejillas de a/c y botón de peligro. (Figura A) 2. Retire (4) tornillos Phillips para quitar la radio. (Figura B) Continúe con el ensamble del kit...
  • Página 7: Ensamble Del Kit

    (Figura A) Nota: El más suave del corte, CORTAR BAR mejor será la 95-7326 se verá en el panel del tablero. 2. Coloque a presión los soportes ISO CORTA AQUÍ DDIN en el borde interior del placa de la moldura ISO DDIN.
  • Página 8: Importante

    Instrucciones de instalación para la pieza 95-7326 IMPORTANTE Si tiene dificultades con la instalación de este producto, llame a nuestra línea de soporte técnico al 1-800-253-TECH. Antes de hacerlo, revise las instrucciones por segunda vez y asegúrese de que la instalación se haya realizado exactamente...

Tabla de contenido