Tughtness Test; Hour Counter; Compression Temp. Speed; Ironer Maintenance - Whirlpool MC/A 150 Instrucciones De Instalación Y De Manutención

E031002AW
G 31 2.35
GPL 2.35
10. TIGHTNESS TEST (gas heating drying
flatwork ironer)
All the pipe unions between the system and the
equipment are subjected to tightness test.
this operation use a leak finder spray ; otherwise
spread on the union points other foaming agents,
which do not cause corrosion. With both the
solutions there should not be any bubbles.
Eliminate possible leaking.
Forbidden to use free flames for the
tightness test.
11. MALFUNCIONING SIGNALS
If there are some
microprocessor gives a complete diagnostic. List
of alarms that could be shown on the display.
AL1
An external object obstruct the iron area and the
save finger slide has been hit: the machine is
positioned in stand-by until the re-establishing of
the correct position of the save finger slide.
AL2
The roller temperature has pass the safe limit.
Put the machine in COOLING, and go on to iron
to assure the integrity of the iron bands until the
temperature go down the alarm limit.
AL3
Temperature probe is broken: it is necessary to
replace it.
AL4 (only for drying flatwork ironers)
This alarm is only for the gas machine after the
third lighting essay. When there is this alarm the
temperature is superior of 80°C, the machine is
positioned automatically on COOLING. Otherwise
if roller temperature is below the 80°C the
machine will stop automatically.
If this alarms appear frequently, call the technical
service.
AL6 (only for drying flatwork ironers)
Pressure fall with the gas supply. If the roller
temperature is superior of 80°C the machine will
be positioned automatically
Otherwise if roller temperature is below the 80°C
the machine will stop automatically. Verify that the
gas valve is open. Eventually call the technical
service.

12. HOUR COUNTER

2.70 2.70
2.70 ---
For
malfunctions, the
on COOLING.
During the machine work a hour counter is
increased and kept in memory between the work
session. To display the hour counter the
"TEMPERATURE" push button "+" and "-" have to
be pushed together just after the machine starting,
when the software version is displayed.
If the working hour number is below 999 the
information is directly displayed, if it is above 999
the hours are displayed as decimal fraction. After
that the hour counter has been displayed, stop
and restart the machine (with the general switch
or with the emergency button).
13. COMPENSATION TEMPERATURE SPEED
It is possibile to operate with both the mangle and
the drying ironer
automatically the speed as the temperature
changes. This change modify the value of the
speed within an interval of ±10% towards the
value of set point. This is an optional, if you wish
to have it installed please ask the constructor,
he will provide all information required for the
resetting of microprocessor

14. IRONER MAINTENANCE

Any ordinary or extraordinary maintenance must
be performed by qualfied staff. Please check that
all the connection are disconnected before
starting any operation. When linen don't slide
through easily (wrinkle or ruling on ironed linen)
proceed to the cleaning of the basin. To clean the
basin pass a thin linen, containing some parafin
powder, one time lapped which must cover the
entire length of the roller. By ironing the lapped
linen the parafin will melt and spread on the basin.
If this operation is not enough, check that the
basin is not covered with solid residual: in this
case the ironer must be disassembled and
cleaned with thin tag. In case of long non
working period, wrap the ironing roller with a
strewed parafin powder sheet. Check every six
months the greasing of the chain of the
movement. Check every three months if the
exhaust fan is clean (for machines provided with
it). Open the left side panel, unscrew the screws
of the scroll and check if clean. The replacement
of sheet and thick flannel is necessary when
first burnings on the ironed linen start showing.
Remember that machine must be used for the
entire length, in order to avoid
concentrated only on certain areas (normally on
the sides of the roller), and the machine must be
switched off only after the temperature of the
basin has dropped under 80°C.
The replacement of the steel wool coverage of
the roller is necessary when the diametres,
completed of rollers and thick flannel, descend
underneath the following values:
- 785 mm of circumference for ironers with 25 cm
of diametre
14
24/11/04
in a way to be able to vary
burnings