Exhaust Flue And Moist Air Duct; Connection; Gas Connection - Whirlpool MC/A 150 Instrucciones De Instalación Y De Manutención

E031002AW

7. EXHAUST FLUE AND MOIST AIR DUCT

The exhaust flue (for drying ironer) must be built
according to the present laws. In case of gas
working machines the chimney must be built away
from inflammable or easy inflammable materials
(at least 500 mm) and with an air-space or with
insulation coating. In case it is impossible to built it
at this distance it will be necessary to protect it
from heat.
The exhaust flue must can be 15 meters long
(diameter 100 mm) and must be insulated or built
with a condensate drainage system. For chimney
over 15 meters, the installer must consult the
constructor.
The exhaust flue , the pipe fitting of the chimney
and the chimney itself must be built according to
the present laws and /or the local and national
regulations. It is compulsery the use of hard pipes;
the connections among elements must be
hermetic, heat- and condensate drainage resistant
and be working-stress resistant. The exhaust flues
without correct dimensions or
amplify the noises of combustion and could give
condensation problems. They could also interfere
with the combustion parameters allowing soots
and deposits to form. To avoid leakage of burnt
gas and noises all the connections must be
hermetic, through high heat resistant materials
(fillers, iron putty, silicon compounds).
Give instructions to the users on the danger of
tampering the exhausting pipes and/or modifying,
plugging, obstructing or reducing the ventilation
openings in the place of
dimensions and the levels of exhausted smokes
and moist air , please refer to enclosed technical
table.

8. CONNECTION

The connection must be installed by qualified staff
and must satisfy the present and/or local and
national regulations. Make sure that the line
voltage is the same indicated on the plate. The
plate data are at the back of the machine. To
connect it, please use a cable type H05 W – F or
more dimensioned according to what is written on
the plate data. Set a differential locking device
with an open contact of at least 3 mm, and
according to the present regulations.
Open the side panel using the key delivered
together with the documentation of the machine.
Remove the panel by rotating it from the base.
Pass the feeding cable through the chock on the
left shoulder of the drying ironer, and connect the
wires, with the help of a screwdriver, to the
following terminals:
: hearth terminal
L1, L2, L3: phase terminal
N: neutral terminal
It is not necessary to verify the direction of rotation
proper shapes
installment. For
13
of the engine, since the suction fans are
monophasic and the engine of the roller is
operated by an inverter..
The machine must be connected to a effective
hearthed system: the
responsible if the connection does not comply with
the present regulations. Before starting any
maintenance disconnect the electric feeding: for
maintenance please refer to the electric diagram
of the machine, inside the left side panel.
9. GAS CONNECTION (only for gas drying
flatwork ironer)
The connection must be installed by qualified staff
and must satisfy the present and/or local and
national regulations. Make sure the gas is the
same indicated on the tech data plate (back of the
machine). To connect use and homologated tube,
this for the entry of gas has ½" diametre and
external tubes have to be conformed to local and
national regulations. To install sth which reduce
the pression on the tube of gas alimentation. To
furnish the manual closing valve.
Pressione di
Tipo
alimentazione
gas
[mbar] MC/A 150
G 20 20 13
G 30 30 o 50 29
G 31 37 o 50 37
GPL 31 30
Diametro ugelli [mm]
Tipo
gas
MC/A 150
G 20 3.80
G 30 2.35
24/11/04
construction is not
Pressione agli ugelli [mbar]
MC/A
MC/A 180
210
14 14
30 27
37 36
30 ---
MC/A 180 MC/A 210
4.05 4.05
2.70 2.70