Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

SAMPLER

10
DN-S3500 has one Sampler of 15 seconds in length. This Sampler can also be looped and scratched during playback.
!1 , !3 , !5 , !6
w, o, !6
i, !0
e, t, !7
q, r, !0 , !6 , !7
y, u
CLR
B TRIM
REV. V V
PITCH/V / / OL.
T
O
T. T T
ET
Record in Sampler
q When the SAMP button is
SAMP.
pushed in the standby or
play mode, the sound from
SAMP point is recorded to
Sampler memory up to 15
seconds.
1
• The SAMP button is flashing while
recording and a 15 sec REC countdown
display will appear. When the recording is
completed, the button turns off and the
corresponding SAMP B LED lights up.
• The remain time of the Sampler memory
is displayed in the character display.
Setting B point
w When the B button is
B
pushed
during
Sampler
recording,
the
Sampler
Loop B point is set and the
loop mode turns on.
2
• Recording continues for approximately 15
seconds without stopping after set B
point.
• If the B point is not set, the recording end
point is set as your B point automatically.
Also EXIT/RELOOP LED light to indicates
Sampler Loop mode is set automatically.
A2
B
EXIT/
B TRIM
RELOOP
CONT. T T
FILE SEARCH
MODE
RELAY
A A
!2 , !4
PARAMETER
P P
S
PUSH ON/OFF
Stop recording
e To
stop
the
sampler
STOP
recording, press the STOP
button at any time prior to
3
15 sec.
• The EXIT/RELOOP LED
light to indicates Sampler Loop mode is
set automatically.
Play Sampler sound
r Playback of the Sampler
SAMP.
sound starts when the
SAMP button is pushed
after
recording
has
stopped.
• Sampler playback continues looping.
When setting a B point, playback loops
4
between A and B point. Without a B point
the Sampler loops the whole recorded
length (about 15 seconds).
t To stop the Sampler sound
push the STOP button.
STOP
• Stutter playback of the
sample is possible when
the
STOP
button
is
pushed repeatedly in the STOP mode.
Select Sampler Loop mode
You can select 1 of 3 playback modes for
Sampler when the Sampler is not playing.
Loop! (default):
Sampler playback continues with
looping.
(EXIT/RELOOP LED stays lit)
Single All!:
Sampler playback continues over B
5
point up to recording length.
(EXIT/RELOOP LED flashes)
Single B!:
Sampler playback stops at B point.
(EXIT/RELOOP LED turned off)
y To select loop mode, push
EXIT/RELOOP button after
recording and before playing.
Exit and Reloop
u The EXIT/RELOOP button
6
can be used same as
Seamless Loop function.
Reverse Play
i You can play the Sampled
sound in reverse by pushing
the REV button. In reverse
play mode REV LED lights
up and the platter spins
7
backwards.
• Reverse playback will take affect when
you push the SAMP button after reverse
mode has been turned on. To return to
normal forward playback, push the REV
button once again.
Moving Sampler B point
o When the B button is
pushed
during
Sampler
8
playback,
the
B
point
moves to the point at which
the button was pushed, and
loop playback from point A starts.
Clearing the Sampler data
!0 During the Sampler stop mode, press the
REV/(CLR) button, while pushing the SAMP
button to clear the Sampler.
CLR
9
SAMP.
REV.
• Or, by pushing the REV/(CLR) button for
more than. 1 sec, you can clear Sampler.
11
ENGLISH
Adjust pitch
The Sampler playback pitch can be adjusted.
!1 Push the PITCH/VOL. button, the pitch input mode
is set, PARAMETERS LED flashes and the current
settings are displayed on the character display.
• Start Sampler playback.
!2 Turning the PARAMETERS knob can change the
pitch.
When pushing down and turning the PARAMETERS
knob, you can change the pitch range 10 times
faster.
Adjust sound level
EXIT/
RELOOP
The Sampler playback sound level can be adjusted.
!3 Push the PITCH/VOL. button again when the pitch
input mode, the sound level input mode is set,
PARAMETERS LED flashes and the current
settings are displayed on the character display.
EXIT/
RELOOP
• Start Sampler playback.
!4 Turning the PARAMETERS knob can change the
output sound level.
!5 Push the PITCH/VOL. button again to turn the
sound level input mode off.
CLR
REV.
Copy from A1/A2 sound
You can copy A1/A2 Seamless Loop into the Sampler
up to 15 sec.
!6 Copy from A1
• When the B button of the Sampler is pressed,
"SAMP
A1" and "Copy/Push Samp" are
0
displayed.
Then quickly push the SAMP button, the copying
is completed within seconds.
!7 Copy from A2
• When the STOP button is pressed, "SAMP
B
A2" and "Copy/Push Samp" are displayed.
Then quickly push the SAMP button, the copying
is completed within seconds.
NOTES:
• You can not copy when the Sampler is already loaded.
• You can copy just your Hot Start A1/A2 points
(without a B point set) for up to 15 sec in the Cue
mode.
ENGLISH
0

Publicidad

Tabla de contenido
loading

Tabla de contenido