Publicidad
co
Please
read these
instructions carefully before you start to
assemble this
product
and carry
out the
steps
in
the order
set
out
in
these
instructions.
When
encountering the information
icon, please refer to the relevant
assembly step for additional comments and
assistance.
Care
and Safety Advice
For
safety purposes we
strongly recommend the product to
be
assembled
by at least
two
people.
Some parts may have
sharp edges.
Please be
careful when handling components.
Always wear gloves, eye
protection, and long
sleeves
when assembling or performing
any
maintenance on your product.
Do
not attempt to
assemble the
product
in
windy
or wet conditions.
Dispose
of
all
plastic
bags safely
-
keep
them out of
reach
of
small
children.
Keep
children away from the assembly
area.
Do
not attempt to
assemble the
product if you
are
tired,
have
taken drugs,
medications or alcohol, or if you
are
prone to dizzy
spells.
When using
a
stepladder or power tools, make
sure
you
follow
the manufacturer's
safety advice.
Do
not climb or
stand on
the
roof.
Heavy
articles should not
be
leaned against
the
poles.
Do
not
hang or
lay on
the profiles.
Keep
roof and gutter clear of
snow,
dirt
& leaves.
Heavy
snow load on roof
can
damage the product making it unsafe to stand
below or
nearby.
Keep
these
instructions
in
a
safe
place
for future
reference.
If
color
was
scratched
during
assembly it
can be
fixed with the
following
tints:
White
-
RAL
9016
Cleaning Instructions
When
your product
needs
cleaning,
use
a
mild detergent solution and
rinse
with cold
clean water.
Do
not
use
acetone, abrasive cleaners, or others special detergents to clean the panels.
Before Assembly
This
product
must
be
assembled on
a
solid, level
base
/
surface (such
as
concrete or
asphalt) and anchored to the ground.
Choose
your
site
carefully before beginning
assembly.
Sort
the
parts and check according to the contents parts
list.
Please
consult your
local
authorities if
any permits
are
required prior to constructing
the product.
Tools &
Equipment
T001
(Supplied)
Notes
During Assembly
When
encountering
these icons, you
are
requested to either
keep
the
screws
slightly
loose
or to fully tighten the
screws.
orl
Steps
Step
8:
Please
apply silicone
sealants above beam
7288
+
7290,
in
order to prevent water from
seeping
in
(drawing
b).
Step 12:
Please
note the profile's direction (8063), the
canal
should
be on
the internal
side.
Step 13: Make
sure
that the angle between the
back wall
profile and the
panel
supporting
profiles
is
90
degrees.
Step 23:
Please
apply silicone
sealants
to the inner edges of parts 7043 & 7042
as
well
as
to the
middle of
parts
7029
+
7039
in
order to prevent water from seeping
in.
Step 24
a
+
b:
Please
apply silicone sealant
on
the inner part of 8116 & 8117
(a)
and
connect to
the profile (b).
Step 24
c:
Adjust the gutter
head's angle according
to your
needs and
tighten screw 4043 from
the
inside.
* It
is
possible to connect standard drainage pipes
(2.07" diameter)
to the gutter
heads' exit.
Step 28: Important!
Please
make sure
the frame
is
perfectly centered before fixing.
Step 31:
Please
do not cut profile 8055 unless needed.
Step 33:
Please
loosen the screws
as
shown
in
diagram
c, set
the
beam exactly on
top of the
poles, once
done re-tighten the
screws.
Step 36:
Important!
Do
not
over
tighten
the
screws.
Use
compatible
screws and masonry
anchors for your type
of
base
/
foundation.
Step 37:
Please
do not cut profile
8056
unless needed.
Step 38:
Please
do
not cut profile 8057
unless needed.
Please
do
not cut the Acrylic
sheets 8111 &
8113
unless needed, all
precautions must
be
taken.
Step 42: Install the sealing strip on the
outer
side,
as
shown
in
the diagram.
Step 47: Note the doors' corners should
be at
a
90°
angle. Should you have
difficulties
in
manipulating the
doors, tap on
the door's corner with
a
rubber mallet.
(Do
not tap directly
on
the corner,
use
a
small
wooden
plank)
Step 51:
Please
note!
The
master
key
attached to the doors,
locks
from the inside.
Step 52: Optional! Part 8531
sets
the grey marked doors, thus creating smaller openings.
*Tighten
all screws
when completing assembly.
Please
note:
Anchoring this product to the ground
is
essential to
its
stability
and rigidity, and required
in
order for your warranty to
be
valid.
The
wall anchoring kit supplied
with
this product
is
suitable only for concrete
walls.
Other wall types need
an
accordant wall fixation
kit.
Publicidad
